Determine the following:a. Enclosed AreaGiven is a thin-walled tube with the following data:Wall thickness- 3mmb. Perimeter of the thin walled tubec. Shear flowTorque is 900 N.mLength of the thin walled tube is 1.2 m.Use G=24 GPa for aluminiumd. Shear stresse. Angle of twistRI00.00ERS0.000,B400.00Unit: mm

The approximate solutions for the angle of twist and shear stress for noncircular tubes are…

Determine the following: Given is a thin-walled tube with the following data: a. Enclosed Area b. Perimeter of the thin walled tube c. Shear flow Wall thickness- 3mm Torque is 900 N.m Length of the thin walled tube is 1.2 m. Use G=24 GPa for aluminium d. Shear stress e. Angle of twist R100.00 RS0.00 B 400.00 Unit: mm

Determine the following: Given is a thin-walled tube with the following data: a. Enclosed Area b. Perimeter of the thin walled tube c. Shear flow Wall thickness- 3mm Torque is 900 N.m Length of the thin walled tube is 1.2 m. Use G=24 GPa for aluminium d. Shear stress e. Angle of twist R100.00 RS0.00 B 400.00 Unit: mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SOM 1. Show your complete solution. ( I know the answers but I need the detailed solution) Given answers: Stress in bar AC = 49468.762 psi Stress in bar CB = 8588.361 psi
ALREADY ANSWERED IN BARTLEBY. PLEASE RESOLVE BECAUSE IT IS INCORRECT! UPVOTE WILL BE GIVEN. WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. SOLVE IN 2 DECIMAL PLACES. BOX THE FINAL ANSWERS.
A flat steel bar, 28 mm wide by 5 mm thick and 1.7 m long, is bent by couples applied at the ends so that the midpoint deflection is 28 mm. Compute the maximum stress in the bar. Use E = 230 GPa. Answer must be in MPa.
A flat steel bar, 28 mm wide by 2 mm thick and 1.7 m long, is bent by couples applied at the ends so that the midpoint deflection is 22 mm. Compute the maximum stress in the bar Use E = 230 GPa. Answer must be in MPa.
A rigid block is supported by three symmetrically spaced rods as shown. Two are made of steel and one is made of brass. Each rod has a cross sectional area of 8-in2. The block weighs 80,000-lb and all three post have the same length before loading. Solve for the normal stress experienced by each post when the brass rod is heated until the temperature increases by 20°F. Use: Esteel=29*103-ksi, Ebrass = 14.6*103-ksi αbrass = 9.8*10-6/°F.
Please answer it properly don't waste my question I will vote it up for your effort thank you.
Complete solution, please. Thanks!
Answer in two decimal places please
Follow-up questions. Rate will be given! c. Calculate the maximum tensile stress in ksi. d. Calculate the angle that the neutral ads makes with the z axis in degrees.
Determine the stress developed in bronze and steel tube after the application of load P. Use Eg = 83 GPa and Es = 200 GPa. P = 50 KN Bronze Steel Tube A = 6361.73 mm? A = 1492.26 mm? E = 83 GPa E = 200 GPa L= 1.50 m L= 1.50 m 90 mm 100 mm
The light rigid bar ABCD shown is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P = 30 kips is applied.
A 52-kip force acts on a machine part at point A as shown below. The diagram shows the internal normal force, shear force and bending moment acting on a particular RECTANGULAR Cross section. -30in N 10in 26in F=52 kip The value of the bending moment M you would use to find the bending stress on a stress element located 2 inches up from the bottom of the rectangular cross section is closest to: 264 kip-in O a. 408 kip-in Ob. 1,464 kip-in O c. 1,608 kip-in