3. A BME student designed a QRS detector for a heart rate monitor. The detector supposed to have aband-pass filter characteristic with central frequency 30 Hz, bandwidth 30 Hz (± 15 Hz around thecenter frequency) and gain of 100 at 30 Hz. He designed the filter and found out that the impulseresponse h(t) = 100e-40£ cos(180t + 12.5°).a. Find the transfer function of the filter.b. Determine the natural resonance frequency (on) and damping coefficient (5) of the filter.c. Draw the frequency response of the filter.d. Does the response meet student's expectations? If not, what parameters need to bemodified and what supposed to be their values?

Dear student as per our guidelines we are supposed to solve only one question in which it should…

3. A BME student designed a QRS detector for a heart rate monitor. The detector supposed to have a band-pass filter characteristic with central frequency 30 Hz, bandwidth 30 Hz (± 15 Hz around the center frequency) and gain of 100 at 30 Hz. He designed the filter and found out that the impulse response h(t) = 100e¬40t cos(180t + 12.5°). a. Find the transfer function of the filter. b. Determine the natural resonance frequency (on) and damping coefficient (5) of the filter. C. Draw the frequency response of the filter.

3. A BME student designed a QRS detector for a heart rate monitor. The detector supposed to have a band-pass filter characteristic with central frequency 30 Hz, bandwidth 30 Hz (± 15 Hz around the center frequency) and gain of 100 at 30 Hz. He designed the filter and found out that the impulse response h(t) = 100e¬40t cos(180t + 12.5°). a. Find the transfer function of the filter. b. Determine the natural resonance frequency (on) and damping coefficient (5) of the filter. C. Draw the frequency response of the filter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2 The signal x(t) = sin(30nt) + sin(70nt) is sampled at 50 samples/sec. The result is passed through an ideal brick-wall lowpass filter with a cutoff frequency of 25 Hz. Compute and sketch the spectrum of the output signal.
Need help steps would be helpful please and thank you!
Circuit Theory
35
Please answer in short like it definitely don't reject in shorts please..
3. Active Analog Filter Topologies You already know from our class discussions that Circuit 1 is an active analog Low-Pass Filter For each of the remaining three circuits, state whether the circuit will function as a low-pass or high-pass filter. Each of your answers must be accompanied by a brief explanation and justification incorporating the frequency dependent characteristics of the reactive circuit elements. That is you should look at the asymptotic impedance of the L and C if the input signal the frequency is very low or very high. Sketch the expected Bode plot for 20 log(Vo/Vs) as a function of log (f) labeling the corner frequencies. No equations are required! R2 R2 R2 R2 R1 R1 R1 Vs Vs o W- Vs Vs Vo Vo Vo Vo Circuit 1 Citcuit 2 Circuit 3 Circuit 4
1.BOlu.. In the system shown in Figure (a), m(t). It represents a low frequency signal with a bandwidth of w Hz. H(), which is the frequency response of the band-pass filter. It is given in Figure (b). Since the output signal is desired to be ze=10-x(+), which of the following must the maximum value of the W bandwidth (in Hz) be lower? x() - m(t)-cos(2400zr1)| () = 10x(1)+x²(1) z(1) Strengthening Band-Pass Filtered Şekil (a) H(S) S(Hz) -1700 -700 700 1700 Şckil (b) Figure (b) O 450 Hz O 550 Hz About 550 Hz O 250 Hz About 250 Hz
3. a) b) Write a short note on Nyquist Rate. Calculate the Nyquist rate in rad/sec and in Hz for, m(t) = 2 sinАnt · cosВnt
Please show complete solution and necessary figures. Thank You!
3
Design a first-order high pass Butterworth filter with a cut-off frequency of 500HZ and pass band gain of 45dB. Given feedback resistor Rr = 220kn. Show all the calculations. Draw the frequency response for the filter
First, I'm trying to use the MATLAB or SciPy function ellipap to find the poles, zeros, and gain for a third-order normalized elliptic lowpass filter with 2 dB ripple in the passband and stopband ripple that has an upper limit of -50 dB. I think I got this part right. Then using one of the programs I need to find the coefficients of the numerator and denominator of the transfer function. Then I need to plot the frequency response. I understand how to use the program for the first part, but I'm unsure how to find the second part. Could you share with me how to approach this? Thank you for your time and help