3) Solve the change in volume of one cubic meter of water when it is subjected to an increase in pressure of 1840 KN Bulk modulus of elasticity is 2.16 X10 GN m²

Q: a) Calculate the Pitch diameter for the following thread. Given the measurement over the wires is…

A:

Q: 127 157 18 11 0) D 24y

A: Let's name the marked lengths in the given figure for calculation purpose.

Q: Ex. #1 central pitch. The dedendum equals 1/P, inch, the clearance is to be one-eight of the…

A:

Q: Bar AB has an angular velocity wAB = 8 rad/s. (Figure 1) AB 200 mm 500 mm e = 45° • PartA Delemine…

A: Solution:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: A four-cylinder engine, with a cylinder capacity of 1385.44 cm3, stroke of 9 cm. Calculate the…

A: GivenV=1385.44 cm3L=9cm

Q: Displacement Volume - Retraction 11 Calculate the volume of the cylinder during retraction.…

A:

Q: An 18 teeth sprocket driving with 98 teeth sprocket at a center distance of 34 pitches. Find the…

A: Approach to solving the question: Detailed explanation: Examples: Key references:

Q: Question 4 ( For the specimen shown, what will be the maximum stress near the hole region (in ksi)?…

A: Given:w=2.49 int=0.25 ind=1 inN=3350 lb NOTE: According to Bartleyby's guidelines we can answer only…

Q: 7) Given the ISO metric hexagon socket screws in the figure; select the correct name of the head…

A: For question number 7 the correct answer is option b. As the first figure is of cap screw and second…

Q: Solidworks. Units are IPS. 24 threads per inch. Primarily just need help designing the threads after…

A: It is asked to draw thread by using Solidworks software

Q: How did you calculate the 233.33 on the second part for the height from the end of the rod DE to the…

A:

Q: Calculation 1. Define torque. 2. Give the expression for torque. 3. Define modulus of rigidity.

A: given; 1.define torque2.give the expression for torque3.define modulus of rigidity

Q: Find the depth of thread in mm for an external thread, if the pitch is 5 mm. Depth of thread (in mm)…

A: Given : Pitch (p) = 5mm   To find : Depth of thread (d) =?

Q: In the figure shown, I=160mm, b=50mm and wAB=1100rpm (clockwise) Solve for (a) the velocity(m/s) of…

A: Length of the connecting rod, l= 160 mm Radius of the crank, b= 50 mm Angular velocity of the crank,…

Q: opic: torsion in circular shafts The hollow shaft used in the system has the following conditions:…

A:

Q: A shell of diameter = 600 mm Height of the shell= 300 mm Height with corner radius=D0.6 mm It is…

A: Given: Diameter of shell, d=600 mmheight of the shell, h=300 mmHeight with corner radius, r=0.6 mm

Q: Different expert. Please help. Written on paper not typed on computer please. Need help on all…

A: Approach to solving the question:Free Body Diagram and Components of weight on the inclined…

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: On the part attached, what is the flatness on the top surface with only the profile applied? And…

A: from the given the top surface flatness must be within  0.4 tolerance zone with respect to bottom…

Q: 150 N r= 25 mm Calculate the equivalent moment at O, taking into account the values given in the…

A:

Q: Match the items in columns I and II. Column-II Column-I P. Charpy Q. Knoop R. Spiral test S. Cupping…

A: Charpy Test   =      Toughness Knoop Test    =       Microhardness  Spiral Test     =…

Q: please calculate at least 3 decimal places a) Draw a sketch where you replace the distributed…

A:

Q: 1- Draw Torque vs. angle of twist for steel specimen

A: INTRODUCTION : Whenever the specimen subjected to the twisting moment that is torque, the stress…

Q: 8. In the assembly, the type of mating or fit between two parts includes clearance fit, interference…

A: There are three types of fits: (i) Clearance fit (ii) Transition fit (iii) Interference fir C :…

Q: Please derive the two Diameter Formula for SI Units. See figure. Thank you so much Dear, your work…

A: Solution:

Q: : A gear with a pressure angle of 25 degrees and a diametral pitch of 5 teeth/in transmits 8 Hp,…

A: Given:ϕ=25°diametral pitch, pd=5 teeth/inPower, P=8 HP =5.9656 KWN=2206 rpmN=60

Q: Anonymous answered this 221 answers a. area of wheel = pi*R² area of 6 cutouts = 6*pi*(R/5)² =…

A: Area of wheel= pi*R^2  Area of 6 cutouts= 6*pi*(R/5)^2 = 0.24*pi*R^2

Q: PS Find Ter, Cower , P for Figure lower 1 below 9, 一E 2.

A:

Q: If the torque and speed values are 125 N-m and 1800 revolution per minute, then the power required…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: Define the various types of fits? Also define fits in terms of shaft and hole basis system

A: Fits is defined as a term that is widely used in manufacturing engineering. It is the assembly…

Q: Write the flexure formula?

A: Flexure formula This formula is used to determine the internal bending stress when an external force…

Q: ) The clearance. b) The whole depth. c) Dedendum.

A: here, you post more than 3 subparts as per honor code and answering guidelines I can answer 1st 3…

Q: OK, so the EA = 108 N, Length (L) = 13 m, and the angle is 22.6. What now?

A: Here you are asking about what to do if the EA = 108 N, Length (L) = 13 m, and the angle is 22.6…

Q: Company XYZ are planning to manufacture a rod made from grey iron as in Fig 1. As a production…

A: Coding is the technique of assigning symbols to pieces that are used for communicating media…

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

A:

Q: The force vs. elongation relationship for a given body is dependent on the body's geometry as well…

A: YES its true.