3 im 43 in. 60 lb 18 in. A i in.

Q: 1.Determine the maximum compressive stress acting on the cross section. 2.Determine the maximum…

A:

Q: Member AC is subjected to a vertical force of 3 kN. Cross sectional area of tie rod is 400 mm2 and…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: The variable section beam has a uniform load w. If it is made of a plate with a constant thickness…

A: A beam of variable depth is given with constant thickness, b. The depth at the support is ho and…

Q: Determine effective stress at point c

A: Given data : γdry=16.5 KN/m3γSat sand=19.25 KN/m3

Q: 3m В G P E 3m C D

A:

Q: Design the maximum permissible value of W using a factor of safety of 2, based on the following…

A: Given Data: The thickness of the support plates are 2 inches. The cross-section of the member is 6×2…

Q: 5 kN is distributed equally among the three rivets, fi e bearing stress between a plate and a rivet;…

A: Given data Diameter, d=25mm Load, P=75kN Thickness, t=25mm The expression for area is given as…

Q: -57. Determine the principal stress, the maximum in-plane shear stress, and ver 120 MPa MADARAKAN…

A: Given data : The value of normal stress in X direction σX=300 MPa The value of normal stress in Y…

Q: The post is fixed supported at its base and the loadings are applied at its end is shown. Determine…

A: Consider the free diagram of the post shown below. Consider the summation of forces in the x…

Q: Determine principal stress and maximum shear stress 200 MPa

A: Given data : Normal stress in X direction (σX)=350 MPaNormal stress in Y direction (σY)=-200…

Q: Determine the maximum safe load P that can be applied in the truss shown in the figure without…

A: Truss is the connection made of different elements like joints, members, or steel connections. Many…

Q: I The force on the 12mm thick link in the figure shown is 2960 N. If the pin has a diameter of…

A: Given,  Thickness = 12 mm Force = 2960 N Diameter of pin  = 10 mm

Q: 1. Calculate the total length, L (m) so that the resulting stress, q is uniform. 2. Which of the…

A: Total load to be restricted -    W = W1L1 + W2L2⇒W = 200×2 + 300×2⇒W =1000KN

Q: diameter of the smallest pin that can be used if not to exceed a shear stress of 60 MPa (Draw

A:

Q: 15. Principle plane is a plane on which the shear stress is O(A) Zero O(B) Minimum OCC) Maximum O(D)…

A: Principal plane is a plane at which their is no stress stress . In Mohr  circle principal stress…

Q: The bar ABC is fixed at A and restricted at C by two 16-mm diameter vertical steel bars, 1500 mm…

A:

Q: Determine the major principal stress, o1 (in MPa). Make sure to enter a positive answer if it is in…

A:

Q: Cm 4m 4m Gom G Gm. F Gm 76 KN 14 76 KN

A:

Q: Determine effective stress at point B and C

A: This question is related to Effective stress from Soil Mechanics. In this question we calculate…

Q: Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: By using method of forces we will find force in AB and BC.

Q: 02: For the stresses at the point shown, find: • The maximum shearing stress. • The principal…

A:

Q: The allowable shear stress is τallow=895 psi�allow=895 psi. The supports at A� and B� are smooth

A: Allowable shear stress - 895 psiTo determine - Largest load intensity

Q: The major and minor principal stresses at the point are 3 MPa and -3 MPa respectively. The maximum…

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Q: The rigid bar Is pinned at A and held by two flexible bars at E and C. The load P Is appled at B.…

A: Given, Yield stress (σy) = 20 ksi  Yield strain (e) = 0.001

Q: -B 2 in. 12 in. 120 lb 4 in. 120 lb 30° -10 in.- 8 in.

A:

Q: Determine the following: a. Maximum and minimum principal stresses b. Normal and shear stresses on…

A: In the above figure we have vertical stress on the body and horizontal stress on the body. The angle…

Q: The stresses at a point along a beam sup- are o, = 2250 psi, porting a sign o, = 1175 psi, and 7 =…

A:

Planar Stresses