(3) A machine part of uniform thickness t = b/2.5 is shaped as shown and machined all over from AISI C1020, as rolled. The design is for indefinite life for a load repeated from 1,750 lb to 3,500 lb. Let d = b. (a) For a design factor of 1.8 (Soderberg), what should be the dimensions of the part? (b)What is the maximum tensile stress in the part as designed?

(3) A machine part of uniform thickness t = b/2.5 is shaped as shown and machined all over from AISI C1020, as rolled. The design is for indefinite life for a load repeated from 1,750 lb to 3,500 lb. Let d = b. (a) For a design factor of 1.8 (Soderberg), what should be the dimensions of the part? (b)What is the maximum tensile stress in the part as designed?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b)Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also gIven pitch = 8mm and coefficient of friction is 0.15?
Required information A shaft is loaded in bending and torsion such that M₂ = 66 N-m, T₂ = 42.496 N-m, Mm = 51.858 N-m, and Tm - 33 N-m. For the shaft, Su = 700 MPa and Sy=560 MPa, the true fracture strength is 1045 MPa, and a fully corrected endurance limit of S₂ = 210 MPa is assumed. Let Kf= 2.2 and Kfs=1.8. With a design factor of 2.0, determine the minimum acceptable diameter of the shaft using the methods mentioned in the subsection. Determine the minimum acceptable diameter of the shaft using the DE-Morrow criterion. The diameter of the shaft is mm.
Two links are connected by a single pin and a tensile force F is applied. The links and the pin are made from Aluminum(sigma_y = 35ksi and T_y = 20ksi). The dimension of the link is 5 inch high by 0.5 inch thick. Find the optimal diameter for the pin and the maximum force,F that can be applied to the linkage before incuring permanent deformation.
Please answer asap I will give u ggod rating if u do not copy. thank u and please solve by yourself.
If the plate thickness in the previous problem were 1 cm, would the thickness be sufficient for a JIC test? Assume these material properties: E = 205 GPa, v = 0.25.
Why did it became 4F/A from F/A, in (a)
A square key fixing a gear on a 30 mm diameter shaft. The shaft is transmitting a power of 18 kW to the gear at 800 rpm. The key is made of steel with a yield strength of 470 N/mm² and the factor of safety is 2.5. The yield strength of the key material in compression can be assumed to be equal to the yield strength in tension. Determine the dimensions of the key.
A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s.,= 345 MPa) for the C-frame material. Calculate the location of neutral axis upto 2 digits after decimal point in mm? 18 mm 38 mm 13 kN 1 10 mm A* 25 mm YA -90 mm 10 mm
Answer is closer to 32 kN/m, but how does it get there?
"A bolt assembly is experiencing 1000 lb of force. The diameter of the head is 5in, bolt diameter is 3in with bolt head height of 1 in. Find the shear stress in psi."
Problem 4 Press-Fit (3-116) Matlab Code is for (3-117) The table gives data concerning the shrink fit of two cylinders of differing materials and dimensional specification in inches. Elastic constants for different materials may be found in Table A-5. Identify the radial interference &, then find the interference pressure p, and the tangential normal stress on both sides of the fit surface. If dimensional tolerances are given at fit surfaces, repeat the problem for the highest and lowest stress levels. Problem Number Material 3-116 3-117 Inner Cylinder di Steel Steel 0 0 do 2.002 2.002 Outer Cylinder D; Material Steel Cast iron 2.000 2.000 Do 3.00 3.00
Thank you for helping me