3(a) A stationary object is acted upon by a number of forces.State the conditions which must be true if the object(i) does not accelerate,(in does not ratate.(b) Fig. 3.1 shows a boat that has been lifted out of a river. The boat is suspended by two ropes.It is stationary.1P1.20 mp.40 m24 kFig. 3.1 (not to scale)The weight of the boat, acting at the cente of mass, is 24 &N, The tensions in the ropes areTand T-Determine(i) the moment of the weight of the boat about the point P.moment(ii) the tension T,.(ii) the tension T

3(a) In this part, it is asking the conditions when the object does not accelerate and does not…

3 (a) A stationary object is acted upon by a number of forces. State the conditions which must be true if the object () does nat accelerate, (in does nat ratate. (b) Fig. 3.1 shows a boat that has been lifted out of a river. The boat is suspended by two ropes. It is stationary. 1.20 m þ40 m 24 Fig. 3.1 (not to scale) The weight of the boat, acting at the cectoe of mass, is 24 &N, The tensions in the ropes are Tand T. Determine (i) the moment of the weight of the boat about the point P, moment =. (ii) the tension T

3 (a) A stationary object is acted upon by a number of forces. State the conditions which must be true if the object () does nat accelerate, (in does nat ratate. (b) Fig. 3.1 shows a boat that has been lifted out of a river. The boat is suspended by two ropes. It is stationary. 1.20 m þ40 m 24 Fig. 3.1 (not to scale) The weight of the boat, acting at the cectoe of mass, is 24 &N, The tensions in the ropes are Tand T. Determine (i) the moment of the weight of the boat about the point P, moment =. (ii) the tension T

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3. Two blocks, A and B, are connected using the cable and pulley system as shown in image below. 60° 30° There is friction between block A and the inclined surface, as well as between block B and the inclined surface. (The cable and pulley system is friction-less and weight-less.) (1) If block B is moving up the incline, on paper, sketch the FBDs for block A and block B separately. In the answer area below, simply enter: "see notes."
A three wheeled OTV has been designed such that the forces from the wheels and motors are uniform, hence the reaction forces at the point of contact with the upper surface can be modeled as a single vertical reaction support. The platform is a square with side length 200mm and has a thickness of 20mm. Plywood has a density of 0.3 g/cm^3. For the purposes of finding the platform weight, W, ignore any holes in the plywood for motor mounts. Due to a misscommunication in the team, the motor mounts M1, M2, and M3 were not attached symmetrically! The potential consequences of this are a difference in reaction forces at the platform to keep it balanced. This difference in reaction forces will result a different normal force at each wheel, and hence the potential for different traction forces, leading to an inability to drive the OTV straight. Co • F: (-75,-75) F₂: (85, -75) • F3: (15,85) -17.4319 MAT 1.338758 3.18886 7 Top View A coordinate system has been defined, such that middle of the…
An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The minimum force P required to prevent rotation of the flywheel is applied. a.) Which Tension is larger, Ta or Tb? Explain b.) What is the angle of contact in radians? c.) What is the value of the ratio Ta/Tb? Please answer these , with FBD and solutions please.
Find the forces (F1,F2,F3 lb) in Fig. 364. (A=27, B=64, C=44) deg, (D=4, E=3, F=4) ft, F4=5440 lb If F4 is negative, then the direction of F4 is down. A negative answer indicates that the direction is reversed. Answers can be checked by demonstrating that components balance.
Looking for simple solution with correct answer.
Given: • Weight of person on merry-go-round = 60 lbs • Force person on merry-go-round is able to hold on with = 60 lbs • radius of bar person is holding onto = 2.2 feet • merry-go-round is accelerated for 5 seconds Find: • maximum tangential acceleration for person to not let go = Your Answer: ft/s^2
I need an answer with a free body-diagram. Show all work as quickly as possible. Question: A wooden plank of negligible mass and length L = 2.8 m is used to keep in balance, horizontally, a small cube of mass 20.0 kg when applying a force F of 80.0 N at one end of the board. The distance, in meters, between the support point of the board and the position where find the cube is: a) 0.56 b) 0.80 c) 1.00 d) 1.12 e) 1.40
h a = 0.9 NA NB On Determine normal forces at A and B. = 3049.74 dA 1855.26 .G You are forced to pull a group of kindergarteners in a cart. You apply a horizontal force of F = 450 N. The cart has a total mass of m = 500 kg with a center of mass at G. Assume the wheels have negligible mass, negligible size (r) and no rolling resistance. d4 = 0.73 m and dg = 1.2 m. You apply the horizontal force at a height y = 0.4 m from the ground. The center of gravity G is located at a height h = 1.2 m from the ground. Determine acceleration of the cart m XN dв X N B y UBC Engineering
A hydraulic press consists of two pistons, the diameter of the largest piston being 55% larger than the diameter of the other piston. Assuming that the hydraulic oil used for power transmission is incompressible and that a force F1 was applied to the piston with the smallest diameter, a force F2 will arise, as a consequence, to the piston with the largest diameter. The F2/F1 ratio is: a.2,40 b.0,42 c.0,32 d.6,20 e.1,55
##L2Q3 The position of a vehicle's center of mass can be determined experimentally. To do this, it is necessary to measure the total weight of the car as well as the forces acting under the front wheels. Fig. 1 illustrates the situation in which the forces acting under the front wheels can be measured experimentally. Considering the data in the figure, determine: a) the position of the center of mass; (b) the force acting on each of the rear wheels. Consider known l, m, and Fz1. 2F C al 2F21 mg
A professor's office door is 0.99 m wide, 2.2 m high, 4.2 cm thick; has a mass of 27 kg, and pivots on frictionless hinges. A "door closer" is attached to door and the top of the door frame. When the door is open and at rest, the door closer exerts a torque of 5.6 N*m. What is the moment of inertia of the door? If you let go of the open door, what is its angular acceleration immediately afterward?