M X L F

a)  Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each piston is 175.00 mm. Calculate the cubic capacity of the engine in cm3 and calculate the clearance volume per cylinder for a compression ratio, r, of 6.25.  The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32 mm and the stroke of each piston is 125 mm. During testing, the engine runs at 1450 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 2.90 cm2 and a diagram length of 0.85 cm. The pressure scale on the indicator diagram is set to 165 kN/m2 per cm. Calculate the mean effective pressure (m.e.p) and the indicated power in kilowatts (kW) developed by this six-cylinder four-stroke engine. Give your answer to 2 decimal places. c)  A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this…

Do not copy paste the solution from outside. The length AB for the lug wrench shown below is 12 inches. What is the maximum force (F) that one can apply on the handles without yielding the material (Steel: Sy = 45 ksi). The diameter of the wrench is 0.625 inch.

Question 4 a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each piston is 175.00 mm. Calculate the cubic capacity of the engine in cm3 and calculate the clearance volume per cylinder for a compression ratio, r, of 6.25. b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32 mm and the stroke of each piston is 125 mm. During testing, the engine runs at 1450 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 2.90 cm² and a diagram length of 0.85 cm. The pressure scale on the indicator diagram is set to 165 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power in kilowatts (kW) developed by this six-cylinder four-stroke engine. Give your answer to 2 decimal places. c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this…

Question 4 a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each piston is 175.00 mm. Calculate the cubic capacity of the engine in cm? and calculate the clearance volume per cylinder for a compression ratio, r, of 6.25. b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32 mm and the stroke of each piston is 125 mm. During testing., the engine runs at 1450 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 2.90 cm and a diagram length of 0.85 cm. The pressure scale on the indicator diagram is set to 165 kN/m per cm. Calculate the mean effective pressure (m.e.p) and the indicated power in kilowatts (kW) developed by this six-cylinder four-stroke engine. Give your answer to 2 decimal c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod…

a)The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm3 ); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm2 and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m2 per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine.

Please no hand writing solution for other wise down vote

Can I get assistance on letting me know if each answer is correct? There are 17 questions in total I think. Thank you

Us (5-5)' High carbon steel or alloy steel can be used for the set of tools on a lathe. The tools must be sharpened periodically. Data for each are as follows: High carbon steel 60 pcs 4h 1h e Alloy steel 70 рсs 6 h 1h Output per hour Time between tool grinds Time required to change tools The wage of the lathe operator is P50.00 per hour, based on actual working hours. The tool changer costs P60.00 per hour. Overhead costs for the lathe are P45.00 per hour, including tool-change time. A set of unsharpened high carbon'steel costs P500 and can be ground ten times; a set of unsharpened alloy steel costs P850 and can be- ground five times. Which type of steel should be used? Solution High carbon steel: cycle time = 4 + 1= 5 hours number of pieces per cycle Cost per cycle: Operator = P50 (4) Tool.changer = (P60) (1) Overhead = (P45) (5) (4) (60) = 240. %3D P200 60 225 %3D Unsharpened tool = P600 50 Total 10 P535

Thank you, I understand it now! What value of g did you use?