3-A 4-mm-diameter and 10-cm-long aluminum fin (k= 237 W/m- C) is attached to a surface. If the heat transfer coefficient is 12 W/m2 C, determine the percent error in the rate of heat transfer from the fin when the in finitely long fin assumption is used instead of the adiabatic fin tip assumption.

3-A 4-mm-diameter and 10-cm-long aluminum fin (k= 237 W/m- C) is attached to a surface. If the heat transfer coefficient is 12 W/m2 C, determine the percent error in the rate of heat transfer from the fin when the in finitely long fin assumption is used instead of the adiabatic fin tip assumption.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

200 W/m K, but the thermal conductivity of Rod 2, 3-130 Two very long, slender rods of the same diameter and length are given. One rod (Rod 1) is made of aluminum and has a thermal conductivity k k2, is not known. To determine the thermal conductivity of Rod 2, both rods at one end are thermally attached to a metal surface which is maintained at a constant temperature Th Both rods are losing heat by convection, with a convection heat transfer coefficient h into the ambient air at Teg. The surface temperature of each rod is measured at various distances from the hot base surface. The measurements = 40 cm from the base is the same as that of the rod of unknown thermal conductivity (Rod 2) at x2 = 20 cm from the base. Determine the reveal that the temperature of the aluminum rod (Rod 1) at X thermal conductivity k2 of the second rod (W/m K) FIGURE P3-130 k=200 W/m K Rod 1 1= 40 cm т, Tа) h, T Rod 2 2= 20 cm T2(x
Q4-A furnace of 100 x 80 x 60-cm inside dimensions is constructed of a material having a C. thermal conductivity of 2.4 W/mK. The wall thickness is 10-cm. The inner surface temperatures is 1000 K and the outer environment is at 20C and 15 /m²C as a convection heat transfer coefficient. Determine the overall heat transfer coefficient based on one-dimension heat conduction analysis. Calculate the heat loss through the furnace wall.
Solve it pls.
Consider one-dimensional, steady-state conditions for the plane composite wall shown be- low. The left surface of wall A is well-insulated with a constant surface temperature of T₁ = 160°C. Heat is generated within wall A at a rate of 5,000 W/m³. The right surface of wall C is maintained at a temperature of T4 = 19°C due to environmental conditions. Assume negligible contact resistance between all interfaces. The thermal conductivity for each wall is listed be- low and the figure indicates the thickness of each wall. (60 points) (a) Find the temperature at interface between wall A and B (x = 20 mm). (b) Find the temperature at interface between wall B and C (x = 85 mm). (c) Sketch the temperature distribution as a function of x for the composite wall. (d) Sketch the heat flux as a function of x for the composite wall. KA = 0.11 W/m.K KB = 0.05 W/m.K kc 0.72 W/m.K T₁ ف A B TA 15 mm 65 mm 20 mm
None
I need the answer as soon as possible
Q1 A composite house wall is constructed from 1.2 cm layer of fiber insulating board, an 8.0 cm layer of loosely packed asbestos, and 10 cm layer of common brick. Assuming convection heat transfer coefficient of 12 W/m?.C on the both sides of the wall. Calculate the overall heat transfer coefficient for this arrangement. Thermal conductivities for building materials are korick= 0.76 W/m. C, koard-0.025 W/m.°C, and kabestos= 0.032 W/m. C)
heat from a small motorcycle engine. If the average engine surface temperature is 112 C, determine the temperature distribution along the fin surface. The thermal conductivity of the Exercise 4.6.4 A circular fin of inner diameter 20 cm and outer diameter of 26 cm transfers Jin material is 21 W/m C and the convective heat transfer coefficient between the Jin and the atmosphere is 120 W/m2 C. Assume an atmospheric temperature of 32 °C. Erongi
A plane wall is 15 cm thick with an area of 1 m2 and has a thermal conductivity of 0.50 W/m-K. A temperature difference of 55oC is imposed across it. Determine the following: A. The Heat Flow B. Conductive resistance
Consider a 10m deep wall with a cross section as shown below. If the temperature on the left side of the wall is 100oC and the temperature on the right side is 30oC, determine: Total thermal resistance of the wall Heat transfer rate through the wall (as a vector) The convective heat transfer coefficient (h) of the air on the left side of the wall if ambient temperature is 120oC
Required information Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k= 1.8 W/m-K, and surface area A= 30 m The left side of the wall is maintained at a constant temperature of T = 90°C while the right side loses heat by convection to the surrounding air at Too = 25°C with a heat transfer coefficient of h = 24 W/m2.K. ok Assuming constant thermal conductivity and no heat generation in the wall, evaluate the rate of heat transfer through the wall. (Round your answer to the nearest whole number) ences The rate of heat transfer through the wall = W
Determine the overall heat transfer coefficient based on the outer area of a 3.81 cm O.D and 3.175 cm I.D brass tube (thermal conductivity = 103.8 W/mk) if the heat transfer coefficients for flow inside and outside the tube are 2270 and 2840 W/m2 k respectively. The unit fouling resistances at inside and outside surfaces are R = R, = 8.8 x 103 m2 KW.