Consider a slab of thickness 10 mm and thermal conductivity of 15 W/m-K. Value of heat transfer coefficient at the left of the slab and right of the slab are 22 W/m² K and 18 W/m² Krespectively. Calculate the overall heat transfer coefficient in W/m².K. Answer Choices: a. 9.84 b. 9 c. 11 d. None of the above

Consider a slab of thickness 10 mm and thermal conductivity of 15 W/m-K. Value of heat transfer coefficient at the left of the slab and right of the slab are 22 W/m² K and 18 W/m² Krespectively. Calculate the overall heat transfer coefficient in W/m².K. Answer Choices: a. 9.84 b. 9 c. 11 d. None of the above

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

GChoose the right answer 1. The temperature profile for steady hest conduction through a plane wall of constant thermal conductivity is a. logarithmic b. parabolic 2. A brick wall (k-0.75 W/mK ) transmits $02 of heat loss through another wall (k-0.25 W/mK, x-100 mm). If the temperature difference across both walls is the same, the thickness of the brick wall would be a.150 mm c. linear 6T b. 240 mm c. 300 mm d. 375 mm 3. The maximum temperature at the center of the solid sphere of radius R having heat generation q (W/m') is given by g'R +9R b. T, + 4k T+9R 6k d. T+9R 8k a. 2k C. 4. The internal thermal resistance of a solid can be ignored if the Biot number is less than a. 1 b. 0.5 c. 0.1 d. Fourier number 5. The ratio of heat transfer of a fin to the heat transfer without fin is referred to as a. fin resistance b. fin efficieney efin effectiveness d. fin conductance.
One-dimensional heat transfer through a composite wall is shown in the following figure. Please calculate the heat flow through the composite wall according to the equivalent thermal circuit. It is known that the thermal conductivity are ka=46.5 W/(m.K), kp=1.1 W/(m.K), kc =0.06 W/(m.K), respectively. The thickness of the three materials is Ax,=Axg=Axc=10mm. The temperature of wall 1 and wall 4 are t=80°C, t4=15°C, respectively. (Please give the compution process and the result.) A - Temperature profile RA Rg Rc T3 Axc A B 1 4 Figure for question 9
Please solve both parts with handwriting please need with correct answer need awesome answer solve both handwriting i requested to u. Part6. An exposed 8 cm external diameter, 20 m long hot-water pipe at 80°C is losing heat to the surrounding (outdoor) air by natural convection. The average outdoor temperature is 5°C. The heat transfer coefficient is 25 W/m2°C. What is the heat loss by natural convection, in kW? A. 9.4 W B. 10.0 W C. 10.4 W D. 11.4 W Part7. A spherical ball with a diameter of 10 cm has an outer surface that is maintained at a temperature of 200°C. It is suspended in the middle of a room that has an average temperature of 20°C. If the surface emissivity is 0.8, determine the rate of radiative heat transfer from the ball to the room in W. (Choose the nearest value) A. 2.3 W B. 4.5 W C. 19.4 W D. 60.8 W
The left side of a composite wall is kept at 300oC constantly. The right side of the same wall is exposed to air at 20oC with a convection coefficient of 32 W/mk. kA = 10 W/mK, kB = 40 W/mK, kC = 1 W/mK, kD = 300 W/mK, kE = 0.1 W/mK Given figure 1, calculate: a) The total thermal resistance of the wall.b) The total heat rate through the wall.c) The junction temperature where B meets D (between second and third column)
6. a. The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls have a thickness of 10 mm and a thermal conductivity of 12 W/m.K. If the wall surface temperature is measured to be 50oC on the left and 30oC on the right, prove that conduction heat transfer occurs at a steady state!b. Heating the iron cylinder on the bottom side is done by placing the iron on the hotplate. This iron has a length of 20 cm. The surface temperature of the hotplate is set at 300oC while the top side of the iron is in contact with the still outside air. To reach the desired hotplate temperature, it takes 5 minutes. Then it takes 15 minutes to measure the temperature of the upper side of the iron cylinder at 300oC. Show 3 proofs that heat transfer occurs transiently
The inner and outer surfaces of a 1-m by 1-m wall of thickness 100 mm and thermal conductivity 10 W/m. C are maintained at temperatures of 35 C and 15 C, respectively. Determine the heat rate by conduction. Select one: a. 2 kW b. 2 MW c. 20000 W
A tube having a cylindrical shape of length equals to 30 m and diameter equals to 10 cm passes through a room. If the temperature of the outer surface of the tube is 110 C and the temperature of the air in the room is 10 C. Determine the rate of heat transfer by convection from the tube to the air. The heat transfer coefficient h = 3 W/m^2.K. Select one: a. 355 W b. 43 kW c. 2827.35 W
A plane wall of an oven with an insulation coating is attached to an insulated wall. The thermal conductivity and thickness of the insulation coating are 0.1 W/(m K) and 1 mm, respectively. The material of the plane wall is stainless steel 304. The density, thermal conductivity, and specific heat capacity of the stainless steel 304 are 7900 kg/m³, 74.9 W/(mK), and 477 J/(kg-K), respectively. The wall thickness of the stainless steel 304 is 15 mm. The temperature of the plane wall with the insulated coating is initially maintained at 30 °C. Suddenly, hot gas with a temperature of 1000 °C enters the oven. The convection heat transfer coefficient at the insulation coating surface is 70 W/(m²-K). Insulation Coating Stainless Steel 304 Oven Gas Perfectly Insulated Wall 1 X L 3-1) What is the overall heat transfer coefficient per unit area from the gas to the surface of the stainless steel? The answer should be given in the unit of W/(m²-K). 3-2) What is the value of the Biot number? 3-3)…
a. The wall of a building has a surface area of 50 m2. The outside layer of the wall is 20 cm thick concrete with thermal conductivity kcon = .8 W/m-K. The inner layer is 10 cm thick balsa wood (kbalsa = .048 W/m-K) as an insulator. Outside temperatures of 47o C are expected, while an inside temperature of 21o C is maintained by the cooling system. Find the rate of heat transfer through the wall.
Define the void ratio in the form of an equation starting from the basic principles.