25mm 25mm 50mm 255mm A 25mm 255mm B 38mm The beam is made from four boards nailed together as shown above and is subjected to the sheer force of a value of 3115 N. If the nails can each support a shear force of 445 N,Calculate 1. The centroid for the transformed cross-section measured from top= mm 2. The moment of inertia of the cross-section about the neutral axis = 10 mm 3. The shear flow in the top nails (nails spaced "s') = N/mm 4. The shear flow per line of side nails (nails spaced 's") = N/mm

25mm 25mm 50mm 255mm A 25mm 255mm B 38mm The beam is made from four boards nailed together as shown above and is subjected to the sheer force of a value of 3115 N. If the nails can each support a shear force of 445 N,Calculate 1. The centroid for the transformed cross-section measured from top= mm 2. The moment of inertia of the cross-section about the neutral axis = 10 mm 3. The shear flow in the top nails (nails spaced "s') = N/mm 4. The shear flow per line of side nails (nails spaced 's") = N/mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
The force of an L-shaped round bar is shown in the figure below. Assuming that bending moment, torque and shear force effects need to be considered, try to calculate the vertical displacement of point C. E of the entire section is 200 GPa, G is 75 GPa, I, J The calculation with A assumes that the radius of the rod is 30 mm.
You don't need to discuss or explain the solution; keep it simple and correct, and respond as quickly as possible.
Can you show how 184 appear? This is the problem: The beam shown in figure is 5 inches wide and 10 inches deep. What is the maximum bending stress?
Derive the singularity equation of moment for the beam shown in figure I then:- 1- Draw bending moment diagram for the beam (by using the singularity- Macaulay's equation) 2- Determine the maximum bending stress in the section (square section with side length of 40cm)
T 10 in Problems 4.54-4.55 4 4.55 The bar has a solid circular cross section. Its polar moment of inertia in in is given by J = 0.1 + 0.15x, where x is the axial position in inches. The shear modulus of the material is G 4.6E6 psi. If the bar is subjected to an axial torque T = 20 in - kip, what is the bar's angle of twist in degrees? =
Two rods vertically connect beams AB and CD as shown in the figure. Point A is fixed supported while point D is hinged connected. If the rod on the right is heated by 18 degree Celsius, 2 m 2 m 2 m Use E = 200 GPa, linear of coefficient expansion = 11.7 x 10 per degree celsius and A = 4500 mm- Calculate the deformation of the left rod in mm Select the correct response: 00468 mm 0168 mm
A wooden bar beam arrangement is shown in the figure. The beam is formed by nailing wooden bar and each nail has a shearing strength of 250 N and the beam is designed for a shear force of 3.2 kN. Find the spacing between the nails for this arrangement. 360 mm 20 mm 200 mm 20 mm ▬▬
QUESTION 1 The assembly consists of two rods and a horizontal bar BC. Each of the rod AB and CD is made of aluminum and has a cross-sectional area of 125 mm2. A point lqad of 5 kN is applied at point E were located 0.20 m from B. Knowing that they support the rigid member BC, calculate the deflection of point E. Modulus of elasticity for aluminium is 75 GPa. P- 5 kN 0.36 m E B C 0.44 m 0.20 m
complete solution please 4 DECIMALS thank you Calculate the moment of inertia (in in^4). Calculate the bending stresses (in psi) at A. Calculate the bending stresses (in psi) at B. Calculate the bending stresses (in psi) at D.
The bolt in (Figure 1) is fixed to its support at C. Figure B in. A 6 in
A steel beam is subjected to a uniform load with length of 8m. Assume that the beam is simply supported. Use Fy= 248 Mpa. Properties of W-shape beam d=229 mm bf=210 mm rf=23.7 mm Tu-14.50 mm kdes=33. 80mm ry=53.80 mm Ix=113 x 10^6 mm^4 Iy-36.9 x 10^6 mm^4 Sx-990 x 10^3 mm^3 Zx 1150 x 10^3 mm^3 J-2100 x 10^3 mm^4 Cu-387 x 10^9 mm^6 What is the nominal shear strength capacity of the section (in kN)?