SteelA = 2000 mm2AluminumA = 900 mm2A = 1800 mm2E = 200 GPaA = 1125 mm²PP2E =70 GPaAP.500 mm+250 mm--450 mm360 mm-FIG. P2.57, P2.58FIG. P2.592.57 The composite bar is firmly attached to unyielding supports. Compute thestress in each material caused by the application of the axial load P = 320 kN.%3D2,58 The composite bar, firmly attached to unyielding supports, is initially stress-free. What maximum axial load P can be applied if the allowable stresses are 80 MPafor aluminum and 144 MPa for steel?304.56KN.

Answered: Image /qna-images/answer/5954fc1e-b459-4b39-8aef-445aea5af127.jpg

2,58 The composite bar, firmly attached to unyielding supports, is initially stress- free. What maximum axial load P can be applied if the allowable stresses are 80 MPa for aluminum and 144 MPa for steel? 304.56KN -

2,58 The composite bar, firmly attached to unyielding supports, is initially stress- free. What maximum axial load P can be applied if the allowable stresses are 80 MPa for aluminum and 144 MPa for steel? 304.56KN -

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve . The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa, Epr 100 GPa. Part A If the bolt is subjected to a compressive force of P = 15.7 kN, determine the average normal stress in the steel. Express your answer to three significant figures and include appropriate units. Ost = Value MPа Submit Request Answer Part B If the bolt is subjected to a compressive force of P = 15.7 kN, determine the average normal stress in the bronze. Express your answer to three significant figures and include appropriate units. Figure HA P Obr = Value MPа Submit Request Answer 10 mm Provide Feedback 20 mm P
The circular column is subjected to a compressive force of 5kN if the stress in the column is limitedto 17.63MPa, what is the limiting value of diameter d?
Question 1c. A bar is having a cross-sectional area of 700mm?, is subjected to axial loads at the position indicated. What is the value of stress in the segment QR? 21KN 2/3 63KN 35KN 49KN P. R Figure O le: Steel har ...
II. A post tapers uniformly from a diameter d at the upper end to a larger diameter D at the lower end, as shown. It supports an axial load of P. Given allowable stress of S, the post's dimension can be determined using the formula o=P/A. For structural safety, what must be the area in this formula? The lower, middle, or upper cross- section of the post? Why? Upper Area Middle Area Lower Area
Problem 1A steel wire is 6 m long, hanging vertically supports a load of 2000N. Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 4mm. E = 200, 000 MPa.
Part 1. A composite assembly of length, L-375 mm, consisting of a steel (G-77 GPa) core (2) connected by rigid plates at the ends of an aluminum [G-35 GPa) tube (1) is shown. The aluminum tube has outside diameter D₁ - 50 mm and inside diameter d₁-30 mm. = 100 MPa, and the The solid steel core has diameter d₂-25 mm. The allowable shear stress of aluminum tube (1) is (rallow) allowable shear stress of steel core (2) is (Tallow)2= 135 MPa. Determine (a) the allowable torque T that can be applied to the composite shaft. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced by the allowable torque T. T D₁ L Calculate the polar moment of inertia, J₁, of the aluminum tube. Answer: J₁ (106) mm².
1. A solid square rod is cantilevered at one end. The rod is 0.8 m long and supports a completely reversing transverse load at the other end of 50 kN. The material is AISI 1060 hot-rolled steel (?? =370 MPa,?? =680 MPa ). Use a design factor of 2 and determine the dimensions of the square cross section for the following cases. Neglect any stress concentration. a. The rod must support this load for 100 cycles. b. The rod must support this load for 104 cycles. c. The rod must have infinite life.
Part A The bolted connection (Figure 1) joins the bar supporting force P to two flanges set into a wall at A and B. In addition to supporting the load transferred by the bolt, the flanges are also subjected to additional 5-kN and 2-kN loads, as shown. Determine the largest internal shear force resisted by the bolt when P= 8 kN. (Figure 1) Express your answer to three significant figures and include appropriate units. Value Units Submit Request Answer Part B Determine the largest internal shear force resisted by the bolt when P = 23 kN and P = 18.6 kN. (Figure 2) Express your answer to three significant figures and include appropriate units. Value Units Figure Submit Request Answer SAN Provide Feedback Next > 2kN
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e� = 55 mmmm and is subjected to the loading shown. Let a� = 200 mmmm , b� = 220 mmmm , c� = 350 mmmm , d� = 250 mmmm , and P� = 3.0 kNkN . Take point A to be at the top of the circular cross-section. As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, Mx��. b) Part B - Moment about the z axis at A Part C - Stress due to the normal force To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm , find the stress σA�� due to the normal force. Part D - Stress due to the bending moment about the x axis To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm , find the stress σA�� due to the bending moment about the x axis.
-8 in.- -8 in.- (a) (b) Which of the following best explains why cylinder (b) has a higher longitudinal stress in its walls compared to cylinder (a)? Assume the gauge pressure of the fluid inside the cylinder is non-zero. O Cylinder (b) is supported at two locations Cylinder (a) is not free to deform in its longitudinal direction The vertical (longitudinal) pressure in cylinder (a) is transferred directly to the [bottom] support, bypassing the cylinder walls None of the above the longitudinal stress for both cylinders is the same
i need the answer quickly
Please give neat and proper step by step solution. A tie rod of uniform section is required to resist a force of 450 kN at an eccentricity of 25 mm from the axis of the rod. Determine the size of the tie rod if the permissible stress is limited to 125 N/mm².