250 mm 400 mm members AD and EG has a 10 x 40-mm uniform rectangular cross section and is made of a steel with an ultimate strength in tension of 400 MPa, while each of the pins at C and F has a 20-mm diameter and are made of a steel with an ultimate strength in shear of 150 MPa. Determine the overall factor of safety for the links CF and the pins connecting them to the horizontal members. 250 mm 1.53 Each of the two vertical links CF connecting the two horizontal A D E F 24 kN

250 mm 400 mm members AD and EG has a 10 x 40-mm uniform rectangular cross section and is made of a steel with an ultimate strength in tension of 400 MPa, while each of the pins at C and F has a 20-mm diameter and are made of a steel with an ultimate strength in shear of 150 MPa. Determine the overall factor of safety for the links CF and the pins connecting them to the horizontal members. 250 mm 1.53 Each of the two vertical links CF connecting the two horizontal A D E F 24 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3) With a given load P = 22.5 kips, two 2 in x 4 in wooden joints are glued together along the joint AB. Determine the normal and shearing stress (in psi) along the glued part.
PROBLEM NO. 2 For the frame shown, a 4998-N load is acting on member ABD at D. If the allowable material shear stress for is 49 MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C. 4998-N 1.00 m 1.59 m 45° 0 O B A 1.59 m 1.58 m
Q2. The pin-connected frame is subjected to the force Fas shown. The dimensions are 4-4.0 ft, - 2.6 ft. and -3.9 ft. Member BC is made of steel (E- 29000 ksi), and has rectangular cross-section, with b- 13 in. and h=4.1 in. The supports at B and Cact as pins for x-x axis buckling and as fixed supports for y yaxis buckling. Determine the greatest load F(in the unit of kip) the beam will support without causing member BC to buckle. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Your Answer:
Question 2 The rods BE and CD are made from steel (E=200 GPa), and each have a diameter, P. The ends of the rods are threaded with a pitch, p. The nuts at B and C are initially finger tightened such that they barely touch rigid member ABC. If the nut at C is then tightened by one full turn, determine: (a) the tension in rods BE and CD (b) the distance, uc, that point C on the rigid member ABC moves. Assume a=300 mm, b= 100 mm, c= 2.5 m, d= 6 m, 0=40 mm, and p=1 mm. OA a В E b D C d
For the frame shown, the wood has a normal failure stress of 42 MPa, and a shear failure stress of 10 MPa. If P = 40 KN and the factor of safety against failure is 2, Determine the required minimum thickness t of member AB. а. 19.76 шп 18.76 mn b. 16.76 mm 17.76 mm Determine the required minimum edge distance b. a. 53.56 mm c. 73.56 mm b. 63.56 mm d. 43.56 mm A 75 mm 40° 40° C в 75/mm
w=15
- once answered correctly will UPVOTE!!
QUESTION 2 Consider that x = 2.76 ft and y = 7.01 ft. B The 5.7-in diameter steel shaft AB is attached into the rigid wall at C and supported by a smooth bearing at A. The lever AC is welded to the end of the shaft. The maximum allowable stress for shaft AB is 355 psi. Determine the maximum allowable force P in lbs. C
Determine the maximum shearing stress and elongation in a helical steel spring composed of 25 turns of 25-mm-diameter wire on a mean radius of 150 mm when the spring is supporting a load of 2.0 kN. Use Eq. A.M.Wahl Formula and G = 83 GPa.
2. A 6 mm diameter pin is used in connection C of the pedal shown. Knowing that P = 500 N. Determine: 1. The average shear stress in the pin. 2. The average crushing effort in the pedal C. 3. The crushing stress in the supports of C. The figure is in the attached image
Problem #1: The following bar has a diameter of 40 mm and is subjected to the loads shown. For the point A determined: 45 N.m 300 mm 5 kN 200 mm B a. The combination of normal and shear stresses b. The maximums and minimums. Indicate the orientation of the principal axes. C. The maximum shear stress. Indicate the orientation of the axes for this effort.