(25) A biomechanical model of the bones and biceps muscles of a person's arm supporting a mass m=2 kg is shown below. The weight of the forearm is 9 N. If the cross section of the tendon AB is 28 mm' what is the average normai stress in the tendon? 290 mm A 150 mm) 200 mm

Q: One end of a steel rod of radius R = 10mm and length L = 90 cm is held in a vise. A force of…

A: solution as .

Q: A cable is replaced by another one of the same length and material but of twice the diameter (a) How…

A: (a) Write the expression for Young’s modulus

Q: Determine the Young's modulus of a 1.50 x 10^-1 m long tendon if it is stretched by 3.70 x10^-3 m by…

A:

Q: "One end of a steel rod of radius R = 10mm and length L = 80 cm is held in a vise. A force of…

A:

Q: 2. The cylinder drawn below represents a portion of an unmyelinated axon. Current flowing through…

A: Given: The resistance of the axoplasm is Ra The resistance of the cell membrane is Rm

Q: One end of a vertical metallic wire of length 2.0 m and diameter 1.0 mm is attached to a ceiling,…

A: Answer:   To determine Young’s modulus of any metal is given as below:     The slope of the above…

Q: Why must the change in the wire's length be measured so accurately although the wire's original…

A: Write the expression for the strain and stress, respectively.

Q: A biomechanical model of the bones and biceps muscles of a person's arm supporting a mass m=2 kg is…

A: Stress is a quantity that describes the magnitude of forces that cause deformation. Stress is…

Q: approximately 25 N of tensile force per square centimeter of cross-sectional area. Calculate the…

A:

Q: To stretch a relaxed biceps muscle 2.5 cm requires a force of 25N. Find the Young’s modulus for the…

A: Force, F = 25 N  stretched length, l = 2.5 cm  length, L = 0.24 m  area, A = 47 cm2

Q: 10) A femur bone of length 30 cm and diameter 2.5 cm is subjected to a compressive tress of 1.5 *10…

A:

Q: One end of a metal rod of radius R =8.7 mm and length L-81 cm is held in a vise, see figure. A force…

A: The expression for the Young’s modulus is,

Q: A wall climber of mass 85 kg dangles at the end of a rope. The rope has a diameter of 9.6 mm, and is…

A: mass= 85 Kg Length, L= 21 m radius, r= 4.8 mm ∆L= 3.2 cm

Q: The compressivestrength of our bones is important in everyday life. Young’s modulus forbone is about…

A: Given that  Youngs Modulus for bone is about 1.4x1010 and that a 1% change in length of bone ca3…

Q: If the curvature of this pole is measured, can the bending stress developed within it be determined?…

A: To determine: The bending stress can be determined, if the curvature of the pole is measured.

Q: Assume Young's modulus of a femure bone of an effective diameter 2.5 cm is 1.5 x1010 N/m2. The bone…

A: Given: A femur bone of an effective diameter 2.5 cm and it's Young's modulus = 1.5 × 1010 N/m2.…

Q: (b) A student is designing a three-legged wooden stool as shown in Fig. 22. Fig. 2.2 The stool must…

A: Answer

Q: A load of 40 kg is suspended from a ceiling through a steel wire of radius 20 mm. Find the tensile…

A:

Q: Assume that Young's Modulus for bone is 1.50 ✕ 1010 N/m2 and that the bone will fracture if more…

A: (a) Let us calculate the cross-sectional area, A of the bone:

Q: 14) An object put on a table with four legs. Both the table and the object together have the same…

A: Since we only answer up to 1 question, we’ll answer the first question. Please resubmit the…

Q: To stretch a relaxed biceps muscle 2.5 cm requires a force of 25 N. Find the Young's modulus for the…

A: We must ascertain the muscular tissue's Young's modulus. We are aware that the biceps muscle can be…

Q: A cable is shortened to half its original length (a) How does this affect its elongation under a…

A: (a) Let Y be the Young’s modulus of the cable, m be the mass of the load, g be the acceleration due…

Q: "One end of a steel rod of radius R = 10mm and length L = 90 cm is held in a vise. A force of…

A:

Q: One end of a steel rod of radius R = 9.5 mm and length L = 81 cm is held in a bench vise. A force of…

A:

Q: " The femur is a bone in the leg whose minimum cross-sectional area is about 4.0 X 10-ª m². A…

A:

Q: Assume Young’s modulus for bone is 1.40×1010 N/m2 . The bone breaks if stress greater than 1.50 ×…

A:

Q: a) Knowing that the allowable stress is 20 ksi, determine the maxi-mum allowable magnitude of the…

A: Calculate the ratios for design purpose. Calculate the  ratio. Here,  is the width of the raised…