(b) A student is designing a three-legged wooden stool as shown in Fig. 22. Fig. 2.2 The stool must be able to support the weight of an adult. The maximum compressive stress of the wood is 2.3 MPa. Estimate the minimum cross-sectional area A of one leg. m2 [3] A = Turn over
Q: A tightrope walker stands on a wire that is supported by a pole at each end. The tightrope walker…
A: Given that the tension in wire is3.42×103 N, and it makes an angle of 6.2°. The young’s modulus of…
Q: 0.25 in. 5 in. 1 in. 0.25 in. -0.25 in. 2.5 in.
A: Maximum axial force P that can be applied to the steel plate
Q: A 226-N object is hung from the end of a wire of cross-sectional area 0.03 cm-. The wire stretches…
A: Given: Force,F=226NArea,A=0.03cm2=0.03×10-4m2Length,L=150cm=150×10-2mChange in…
Q: A cylindrical steel wire that is 2 m long must stretch no more than 0.25 cm when the applied tensile…
A: The objective of this question is to find the minimum cross-sectional radius of a cylindrical steel…
Q: Asolid copper cube has an edge length of 85.0 cm. How much stress must be applied to the cube to…
A: Here in this Question The Edge length of the copper cube is given to be 85.0 cm and it has been…
Q: The beam is supported by a pin at C and an A- 36 steel guy wire AB. If the wire has a diameter of…
A: Solution:-Given thatDiameter of the wire (d)=0.2 inuniformely distributed load (w)=1000 lb per ft
Q: A high-carbon steel wire, circular in cross-section, has a diameter of 14 mm. What is the force (in…
A:
Q: Find the stresses in members BC, BD, and CF for the truss shown in Indicate the tension or…
A:
Q: What is the compressive stress F/A on a woman's feet, in units of kilopascals (kPa) , if the woman's…
A: Given Data: The mass of a woman is, m=52.0 kg The area of each shoe is, A=185.0 cm2 The effective…
Q: Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P…
A: Consider the given data as below. Diameter of wire CD, dw=18 inch Diameter of the pin at B, dp=18…
Q: A cable used to lift heavy materials like steel I-beams must be strong enough to resist breaking…
A: Given,Force, (a) To find the cross-sectional area A:Taking the average ultimate tensile strength of…
Q: A cable is 10.0 m long and has a diameter of 2.00 mm. A force of 45.0 N is applied to the end of the…
A: Length of Cable L=10 m Diameter of the cable d=2.00mm=2*10-3m Force applied to the End of the cable…
Q: A biomechanical model of the bones and biceps muscles of a person's arm supporting a mass m=2 kg is…
A: Stress is a quantity that describes the magnitude of forces that cause deformation. Stress is…
Q: a)What is the magnitude of the bone shear force acting on the vertebra?Report in N b)what is the…
A: The objective of the question is to calculate the magnitude of the bone shear force and the bone…
Q: A cable used to lift heavy materials like steel I-beams must be strong enough to resist breaking…
A: Given, Force, F=1.7×106 N (a) To find the cross-sectional area A: Taking the average ultimate…
Q: The beam is supported by a pin at A and a short link BC. Figure 0.5m 1 m 4P 1.5 m 4P 1.5 m 0.5m 1 of…
A:
Q: A steel cable 1.70 m in length and with cross-sectional radius 0.380 mm is used to suspend from the…
A: Length of cable (L) = 1.70 m cross sectional radisu (r) = 0.38 mm mass (m) = 20 kg angular speed =…
Q: ó vértical forces are ce ái Determine the ma: BC of the beam.
A: RA + RD =20 kNDue to symmetrical loadingRA = RD =10kNB and C moment is constant and also…
Q: A cable used to lift heavy materials like steel I-beams must be strong enough to resist breaking…
A: In this case, the tensile strength σ=250 MPa=2.5×108 Pa The force, F=1.3×106 N
Q: The bulk modulus of a material is 5.62 × 1011 N/m2. What fractional change in volume does a piece of…
A: bulk modulus of a material is 5.62 × 1011 N/m2. What fractional change in volume does a piece of…
Q: A 115 m long steel cable with a cross-sectional area of 1.13 x 10-4 m2 is subjected to a tensile…
A: Given- Length L= 115 m Cross-sectional area A= 1.13 x 10-4 m2 Tensile force F= 565 N
Q: A tightrope walker stands on a wire that is supported by a pole at each end. The tightrope walker…
A: Solution: Given that The tightrope walker creates a tension T = 3.42 ✕ 103 N in a wire making an…
Q: A hollow cortical bone has a maximum compressive stress of 185 MPa. This bone has an area of 6.4…
A: Write the given values with the suitable variables. σ=185 MPa=185×106 PaA=6.4 cm2=6.4×10-4 m2 Here,…
Q: A steel rod 55 cm long has a diameter of 30.0 cm. The compressive strength (the maximum stress it…
A:
Q: What is the compressive stress ?/?F/A on a woman's feet, in units of kilopascals (kPa)(kPa) , if the…
A: mass = 66 kg weight = 66 * 9.8 = 646.8 N weight on each foot = 646.8/2 = 323.4 N Area of each shoe…
Q: A marble column of cross-sectional area 0.80 m2 supports a mass of 18000 kg. The elastic modulus for…
A:
Q: 66. A cable can support only a compressive or “pulling” force. True False 67. In…
A:
Q: A tightrope walker stands on a wire that is supported by a pole at each end. The tightrope walker…
A: F = 3.42 × 103 N L = 16 m d = 0.50 cm = 0.0050 m θ=6.2°
Q: The two structural members, one of which is in tension and the other in compression, exert the…
A: We have two forces F1=4.2 kN which makes an angle of 63o with the +x axis directed inwards and…
Q: Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have,…
A: Solution: The given diagram is redrawn as given below.
Q: Problem 2 P A 40 kips 30 in. 30 kips B 30 kips 40 in. Two solid cylindrical rods AB and BC are…
A: We have to find the force P
Step by step
Solved in 2 steps with 1 images