220 5V SV Fig. (1) 3 University of Basrah College of Engineering Department ef Computer Engineering First Year Electrical Circuit Lab SV SV R3 Fig (2) Table (1) 1; (mA) Vec (volt) Delta 1(mA) L(mA) Vaa(volt) Vealvolt) Connection (Measured Values) Delta Connection (Calculated Values) h (mA) G(mA) Va(volt) Vec (volt) VCa(volt) Star Connection (Measured Values) Star Connection (Cakulated Values) 560

Q: 5. Design a device using 8051 to let the user choose between 9,600 or 19,200 baud rates. The user…

A: Hello reads today i am writing about serial communicationof data in one of the most widely used…

Q: 5. What are the fundamental differences between the two circuits shown in Figs.5 and .6? Do the…

A:

Q: Q3: For the Digital-to-Analog converter circuit shown in Fig. 1, if the LOW state voltage is 0 Volt,…

A:

Q: Q3. 3 Cyclo- converter supplied with alternative voltage V=150 v and input frequency 1 MHz find the…

A: The answer as given below:

Q: Analyze the following simple PV/battery system which includes four PV modules, four batteries and an…

A:

Q: 120 marks Q3: Draw the resulting output signal for all the shown circuits with given inputs b) A 10%…

A: Part (a)This appears to be a simple rectifier circuit. The input is a sinusoidal waveform with a…

Q: 8) For the circuit shown below determine (a) the node-pair voltage V, (b) currents through all the…

A: Here i have done nodal and found the answer.

Q: Q5. A full-wave bridge rectifier circuit is shown in Fig. Q5. Forward voltage of each diode 0.7V;…

A: This is full wave Rectifier.  We know, in transformer Vp /Vs = N1 /N2   Forward bias voltage drop of…

Q: Q.1: Draw the output voltage of the circuit shown below, if the input voltage 11Sinwt. R DYS: E-…

A: The diode is ON when the voltage across anode is more than the cathode voltage. It is known as…

Q: a) Find the Q-point (Io, Vos) of the enhancement mode NMOS transistor in the following circuit. Rp…

A: Fig: Given NMOS transistor Formula for ID is given by

Q: 3.68 A digital circuit is required to display a digital signal on a bar-graph LED, similar to a…

A: As per the given information, we need to:a) write the truth table with D1 and D0 as inputs and Y1,…

Q: d. On an approximate basis, how are Ig and Ic related based on the results above? 14. a. Using the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: 10 VDD=+12 V 8.0 Rp 1.0 k2 6.0 Ip (mA) 4.0 2.0 Ro 10 MQ Rs -5.0 -4.0 -3.0 -2.0 -1.0 Vos (V) (b)…

A: In this question,  We need to determine the voltage VGS  if voltage Vs = 2.7V

Q: 3.6 Common-Collector Configuration 26. An input voltage of 2 V rms (measured from base to ground) is…

A:

Q: NMOS Current Mirror System NOTE 1: Watch your signs for NMOS and PMOS current conventions! NOTE 2:…

A: The given circuit is as shown below,

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.