200 stress, σ (MPa) 0.01 0.03 strain, &

Q: 1. A steel rod 500mm long and 20mm× 10mm in cross-section is subjected to axial pull of 300 KN.If…

A:

Q: the natural strain at point B (ɛg

A: Given data; The true stress ,true strain diagram of a strain  hardening material shown in fig,…

Q: Consider a linear rectangular thin sheet of metal, subjected to uniform uniaxial tensile stress of…

A:

Q: a) Figure Q4 (a) shows an L-bracket ABC with diameter d which lies in the horizontal plane. It is…

A:

Q: 40-mm sides glass polymer fibers composite cube shown in Figure.2. The Glass polymer fibers aligned…

A: INTRODUCTION: The internal force per unit area of the cross-section is termed as stress. Stress is…

Q: A material is deformed under a pure shear stress as shown in the following figure. Calculate the…

A:

Q: (B) – Figure Q4/B show the bone has an outer rac of 15 mm and thickness 3 mm. Determine the strains…

A: Draw the diagram for the axes given in the problem. Understand that in the given figure, the shaft…

Q: The longitudinal strain in a cylindrical bar of diameter 20mm and length 2.5m during the tensile…

A:

Q: A cylindrical specimen of steel alloy (stress-strain behavior shown in figure) having a length of…

A:

Q: A bar produces a lateral strain of -70 × 10-5 when subjected to tensile stress of magnitude 400 MPa…

A: Given, Lateral strain = εl = -70 x 10-5 Tensile axial stress = σ = 400 MPa Poisson's ratio = μ = 0.3…

Q: A circular rod of length 18 cm and diameter 5 mm is made of grade 1045 grade steel. a. Calculate the…

A:

Q: (a) the strains in these directions, (b) the changes in dimensions, (c) the volumetric strain and…

A:

Q: The length of a wire increases from 1.25 m to 1.2508 m when a load of 12 kg is suspended. The radius…

A:

Q: 3. If the engineering strain in a tensile bar is 0.0025 and Poisson's ratio is 0.33, find the…

A:

Q: The figure below shows a hollow circular beam with an outside diameter of 150 mm and a wall…

A:

Q: A thin metal alloy plate is loaded by biaxial stress (2 directions) given by 8000 psi in the x…

A:

Q: A wire of length L = 25 m and diameter d = 1.6 mm is stretched by a tensile force of P = 660 N. The…

A:

Q: Determine the loss of head due to sudden enlargement when the velocity of water in the smaller pipe…

A:

Q: Given the shear modulus(G) for aluminum as 2.4e+10 N/m2 and the shear strain is given as 6e-5. What…

A: From hook's law  Shear stress is directly proportional to shear strain within elastic limit

Q: A rod is subjected to a uni-axial load within linear elastic limit. When the change in the stress is…

A: This question is a very simple and related with the concept of Young's modulus of elasticity and…

Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…

A:

Q: Find the resulting strains in a unidirectional lamina subjected to normal tensile stresses of 20MPA…

A:

Q: A circular tube is subjected to torsion by torques T applied at the ends. The bar is 0.75 m long and…

A: The above question is based on Torsion due to Torque which is applied at the ends.

Q: The true stress (6), true strain (8) diagram of a strain hardening material is shown in figure.…

A: Given data: The stress at point A is σA = 500 MPa. The strain at point C is εC = 0.5. The Young's…

Q: Two hard rubber blocks with Modulus of Rigidity equal to 350 kPa are used in an anti-vibration mount…

A:

Q: Sketch two more stress-strain diagrams, again one for a ductile material and one for a brittle…

A: Stress and strain: Stress is defined as the internal resisting force per unit area; it represents…

Q: 40-mm sides glass polymer fibers composite cube is shown in Figure.1. The Glass polymer fibers…

A:

Q: A circular rod of diameter 8 mm and 300 mm long is subjected to a tensile force 20 kN. Take E =…

A: Given data:

Q: 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given…

A: