Project 2:40-mm sides glass polymer fibers composite cube is shown in Figure.1. The Glass polymer fibers aligned in thex direction. The cube is constrained against deformations in the y and z directions and is subjected to acompression load of 65 kN in the x direction. Estimate the strain, change in length and stresses in x,y, andz directions as well as determine the volumetric strain. Illustrate the effect of two and three-dimensions byconstructing appropriate sketches. If the cube is only constrained against deformations in the y direction,describe the changes in two and three-dimensions by constructing appropriate sketches.E,= 50 GPaE, = 15.2 GPa v = 0.25415.2 GPa=0.254%3D0.42S

Answered: Image /qna-images/answer/e5f1bfde-6b85-4e97-b16e-a790ff80c64e.jpg

40-mm sides glass polymer fibers composite cube is shown in Figure.1. The Glass polymer fibers aligned in the x direction. The cube is constrained against deformations in the y and z directions and is subjected to compression load of 65 kN in the x direction. Estimate the strain, change in length and stresses in x, y, an z directions as well as determine the volumetric strain. Illustrate the effect of two and three-dimensions b constructing appropriate sketches. If the cube is only constrained against deformations in the y directio describe the changes in two and three-dimensions by constructing appropriate sketches. E.= 50 GPa E. = 15.2 GPa v= 0.254 E. 15.2 GPa v,= 0.428 v = 0.254 %3D %3D %3D %3D

40-mm sides glass polymer fibers composite cube is shown in Figure.1. The Glass polymer fibers aligned in the x direction. The cube is constrained against deformations in the y and z directions and is subjected to compression load of 65 kN in the x direction. Estimate the strain, change in length and stresses in x, y, an z directions as well as determine the volumetric strain. Illustrate the effect of two and three-dimensions b constructing appropriate sketches. If the cube is only constrained against deformations in the y directio describe the changes in two and three-dimensions by constructing appropriate sketches. E.= 50 GPa E. = 15.2 GPa v= 0.254 E. 15.2 GPa v,= 0.428 v = 0.254 %3D %3D %3D %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The structure shown in Fig. la is subjected to loading P and T. A set of strain rosette is positioned at point A for strain measurement. The orientation of the strain rosette is shown in Fig. 1b. The material properties are given as E = 200 GPa, G = 77 GPa and v = 0.3. If P = 10 kN and T= 250 Nm, find the following: i. The state of stress at point A and sketch the stress element. ii. The principal stress at point A and sketch the stress element. iii. The principal strain at point A and sketch the strain element. iv. The values of each strain gauge (Ea, Eb and ɛc). V. Name one change that can be done to lower the strain value at point A. 50mm 75mm 120 120° T Ø 50mm Ø35mm Fig. la Fig. 1b -----
2. The discs in the spinal column can withstand a stress (force per unit area) of 1.1 x 107 N/m2 before they rupture. (a) If the cross-sectional area of your discs is 10 cm2, what is the maximum force that can be applied before rupture takes place? (b) Estimate the stress at a disc located at the level of the center of gravity of your body when you are standing vertically. (c) What types of situations might the body experience where the stress on this vertebra would be much larger than in (b) above?
answer quickly
Identify the material as shown in figure below. Strain O Linear elastic material O Rigid Material O Perfectly plastic material O Elastic plastic material Stress
You compress a cylindrical biological sample with an engineering stress of -1 MPa. The sample is made of an isotropic elastic material with Young's modulus of E = 10 MPa and Poisson's ratio v = 0.3.(a) Calculate the engineering strains in the direction where the stress is applied and the transverse direction.(b) How much elastic strain energy is present in the deformed sample if it has a volume of 10 cm3?(c) The material has a hysteresis of 0.1. How much energy will you be able to recover when the sample is relaxed?(d) Calculate the true stress and true strain in the compressed sample.
A solid bar of length L = 4 m and diameter 200 mm is heated from 20 to 320 degrees celsius and restrained between two solid immovable walls. Young's modulus of the material is 90 GPa and the coefficient of thermal expansion is 22 x 10-6/°C. →Calculate the thermal strain, e, in micro-strain correct to two decimal places. micro-strain. Calculate the thermal stress, o, in megapascals (MPa) correct to two decimal places. E: σ: MPa. Hence calculate the force exerted by the bar in meganewtons (MN) correct to two decimal places: F MN. L
I need the answer quickly
Please don't copy paste