200 kg/min of steam enters a turbine at 40 bar with 100 degrees of superheat through a 7.5 cm diameter pipe and exits as saturated water at 5 bar through a pipe of the same diameter after expanding adiabatically. The inlet and outlet pipes are at the same vertical height. How much work (in kW) is produced by the turbine?Hint: You might be tempted to neglect the change in kinetic energy between the inlet and outlet.If you choose to do so, you must justify this assumption with a calculation.

Q: Air is to be compressed from 3 bar and 303K to pressure of 15 bar in a multistage compression…

A: a multipart question about a simply supported beam subjected to a thermal load and an axial point…

Q: an insulated piston-cylinder assembly initially at constant pressure of 250 kPa There is 4 L of…

A: Given data:   Pressure of piston-cylinder assembly = 250 kPa Volume of saturated liquid water = 4 L…

Q: In order to increase the velocity of steam used as a fluid for a power plant, it was concluded that…

A: Nozzle is a device which is used to increase the velocity of fluid. Given data: Mass flow rate of…

Q: • 200 kg/min superheated steam at 40 bar and 350C enters a turbine through a 7.5cm ID pipe. It exits…

A: Superheated heated is expanded through a turbine.

Q: 1. At the Shell oil refinery, the lubricating oil, at a velocity of 6 feet per second, is passed…

A: The film temperature of the oil is, Tf = Ti+To2Tf = 105+902Tf = 97.5oF At this film temperature, the…

Q: The turbine in a hydroelectric power plant receives water at a rate of 120 m3/s from an elevation of…

A: The power output from the hydro-electric power plant is to be determined.

Q: a- the volume flow rate of air at the inlet b- the mass flow rate of air at inlet and at exit c- the…

A: HGGHH

Q: If the suction pressure of compressor equal to discharge pressure then the work of compression for…

A:

Q: A converging-diverging nozzle is used to accelerate water at the state of superheated steam. The…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: 8. Problem 2-33 (modified), Davis and Cornwell, Introduction to Environmental Engineering, 6th Ed.:…

A:

Q: Find the average power of the paddle wheel in kW During a constant-pressure process in a cylinder…

A: The average power for the wheel of a paddle is to be determined in kW.

Q: Turbines in a hydroelectric power plant receive water from a 100-m high dam, generate power and…

A: Given data: Height of the dam = 100 m. Diameter of the plant = 6 m. Velocity of the water = 15 m/s.…

Q: Air enters an electric furnace at 100 kPa and 28°C with a volume flow rate of 22 m/min. At the exit…

A: Given that :At entering P1  =100KPaT1   =28 C  =28+273.15 = 301.15 KQ = 22 m3minAt exit P2  = 100…

Q: Q2/ Steam at 320 °C and 80 bar enter Nozzle with velocity 70 m/s and leaving by temperature is 100…

A:

Q: Steam flows into a turbine at the rate of 5 kg/s and 15 kW of heat are lost from the turbine.…

A:

Q: It is proposed to design and develop a Rankine cycle Steam Power Plant in which steam at 80 bar and…

A: Note: Since we are entitled to answer only 3 sub-parts, we’ll answer the first 3 subparts. Please…

Q: Steam at 320 °C and 80 bar enter Nozzle with velocity 70 m/s and leaving by temperature is 100 °C,…

A:

Q: Single acting single cylinder compressor with diameter (15cm) and stroke length of (22.5cm). The air…

A: This problem is based on the concept of isothermal efficiency. Data given : 1. Stroke length , L =…

Q: Water is the working fluid in a Rankine cycle. Steam enters the turbine at 10 MPa and 550°C. The…

A: Note: We are supposed to answer only three subparts of a problem as per our guidelines. Kindly send…

Q: Air enters an insulated compressor at ambient conditions, 100 kPa, 20C at the rate of 0.2 kg/s and…

A: Given: P1 = 100kPa T1 = 273+20 = 293K m = 0.2kg/sec T2 = 500K n= 70% Cpo= 1.004kJ/kg.K

Q: Power for Pumping in Flow System. Water is being pumped from an open water reservoir at the rate of…

A: Given data: Mass flow rate of water = 2 kg/s Length of pipe = 1500 m Frictional losses in the system…

Q: information er a 210-MW steam power plant that o ple non-ideal Rankine cycle. Steam e ine at 10 MPa…

A:

Q: A Diesel cycle releases 1750 J/mol of heat. The pressure and temperature at the begin- ning of the…

A: Given, The heat rejected, Qr=1750 J/mol The pressure  PC=1 bar The temperature, TC=50°C=50+273 K=323…

Q: In a certain gas manufacturing plants, they presented a horizontal tube in which a gas assumed to be…

A: Given data: Initial temperature of N2 = 761.67 0R Initial velocity = 5.6 mph Final velocity = 180…

Q: Using the first law of thermodynamics, analyze the cycle below in the thermodynamic equipment to…

A:

Q: A Compressor compresses the air at 112 kPa and 300 K to 415 kPa and its inner diameter is 0.021 m.…

A:

Q: At the commencement of compression in the reciprocating compressor of a refrigeration plant the…

A: Given:The compressor follows  at To find the work done, Internal energy and heat transfer through…

Q: For the same compression ratio both Otto cycle and Diesel cycle are equally efficient Efficiency of…

A:

Q: Power for Pumping in a Flow System. Water is being pumped from an open water reservoir at the rate…

A: Water is pumped from an water reservoir to a storage tank place 20 m above the reservoir. Both…

Q: Water vapor at 5 MPa pressure and 400 C temperature enters a nozzle at a speed of 80 m / s and…

A:

Q: If a 4" pipe was used throughout the system, what is the fluid velocity at T1 and at T4?

A: the given molar flow rate si converted into mass flow rate. The mass flow rate is obtained in…

Q: Question Three Air flows steadily adiabatically through a pipe with a constant cross-sectional area.…

A: P° = 900 Kpa  T0 = 300 K  P1 = 750 Kpa  T2 = 275 K  K for air = 1.4

Q: Consider a steam power plant operating on the simple ideal Rankine cycle. The steam enters the…

A: State: 1  At P1 = 100 KPa         h1 = hf = 417.44 KJ/Kg       -----------(1)  v1 = vf = 0.001043…