20. The two portions of member AB are glued together along a plane forming an angle 0 with the horizontal. Knowing that the ultimate stress for the glued joint is 2.5 ksi in tension and 1.3 ksi in shear, determine the range of values of 0 for which the factor of safety of the members is at least 3.0.

Q: Q1 The curved portion of the bar shown has an inner radius of 20 mm. Knowing that the allowable…

A: Given,

Q: Determine the value of Q so that the deformation at A is zero.

A: Given:E = 70 GPaP = 3.5 kNDiagram is givenTo find:Value of Q so that the deformation at A is zero

Q: A tensile stress is to be applied along the axis of a cylindrical brass rod that has a diameter of…

A: given; diameter (d)=10mmchange in diameter (δd)=2.5*10-3mmelasticity(E)=10.1*104MPapoisson's…

Q: For the connection shown, the average shear stress in the 18-mm- diameter bolts must be limited to…

A:

Q: 1. The structure is used to support a distributed load of w = 15 kN/m. The bolts at A, B, and C each…

A:

Q: The compressed air tank AB has a 250-mm outside diameter and a 10-mm wall thickness. The arm BC is…

A: Stress calculations:

Q: ogeth le of 25° with the horizontal. Knowing that the allowable str 0 kPa and t = 600 kPa, determine…

A:

Q: 5 mm 20 mm 5 mm Steel core E = 200 GPa Brass shell E = 105 GPa 5 mm 20 mm .5 mm 250 mm

A:

Q: Knowing that for the beam shown the allowable stress is 80 MPa in tension and 100 MPa in…

A:

Q: ! Required information Two horizontal 5.5-kip forces (P) are applied to pin B of the assembly shown.…

A:

Q: A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: (i) Stess at secion X-Xσ=P(b-ϕn)A=1000 X 103(100-25) X 12σX-X=111.1MPawhere b and T→ width and the…

Q: The lap joint is fastened by 5 one-inch diameter rivets. For P = 10 kips, determine (1.) the maximum…

A: Givenn=5d=1inP=10kipst1=34int2=58inw=4in

Q: 1. Links AB and AC and AD have cross-sectional areas of 80 mm, 30 mm² and 80 mm², respectively. The…

A:

Q: Link BC is to be made of a steel for which the ultimate normal stress is 250 MPa. Determine the…

A:

Q: Why is the net area for AB (0.045-0.0102) * (0.012) ? Why is AB in tension and BC in compression

A:

Q: The 1.4-kip load P is supported by two wooden members of uniform cross section that are joined by…

A: Given Data: The load on member is P = 1.4 kip. The cross-section area is A = 3 in ×5 in. The angle…

Q: A 12-kN tensile load will be applied to a 50-m length of steel wire with E= 200 GPa. Determine the…

A:

Q: THE FRAME SHOWN CONSISTS OF FOUR WOODEN MEMBERS, ABC, DEF,BE, AND CF. KNOWING THAT EACH MEMBER HAS A…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.