20. In a repair shop compressed air is used to operate pneumatic tools. The total length of the airline including all the loss coefficients in terms of equivalent length is about 152.5 m (500 ft). The airline consists of smooth pipe of I.D. = 1.27 cm. Air is compressed to 0.345 MPa (50 psia) and then cooled to 24 C (75 F) when entering the line at a velocity of 2.4 m/s (8 ft/s). Find pressure when air is used to operate the pneumatic tool. %3D - To Pneumatic tool Air intake Compressor

20. In a repair shop compressed air is used to operate pneumatic tools. The total length of the airline including all the loss coefficients in terms of equivalent length is about 152.5 m (500 ft). The airline consists of smooth pipe of I.D. = 1.27 cm. Air is compressed to 0.345 MPa (50 psia) and then cooled to 24 C (75 F) when entering the line at a velocity of 2.4 m/s (8 ft/s). Find pressure when air is used to operate the pneumatic tool. %3D - To Pneumatic tool Air intake Compressor

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need help on this question: According to the question: a) If the pipe connected to the pump inlet has a diameter of 24 mm with length (LCP) of 5 m and Darcy friction factor of 0.03, what would be the actual head rise across the pump for a case where the pump outlet pressure is 200 kPa? The difference in height between pump inlet and outlet is 0.25 m, the tank exit is sharp-edged, and the water level in the tank to the tank exit pipe (HWL) is 2 m. Also, consider that the flow velocity inside the tank is negligible. The value of the actual head rise across the pump is = ? b) What would be the pump motor power if the efficiency is 60%? The value of the pump motor power is = ?
A pipe line of length 2000 m is used for power transmission. If 110 kW power is to be transmitted through the pipe in which water having a pressure of 490.5 N/cm2at inlet is flowing. If the pressure drop over the length of pipe is 98.1 N/cm2and ff = 0.0065.Determine:The diameter of the pipe and the volume flow rate; and If a nozzle is introduced at the end of the pipe, what would be its diameter and the power transmitted.
answer first item only
S CE - Oil is transported from A to B along a pipe of constant diameter. The pipe is inclined at 50° to the horizontal and B is at the higher elevation. Considering the flow from A to B, which statement is correct? O The pressure head is decreasing and the velocity head is increasing. O The pressure head is increasing and the velocity head is decreasing. O The pressure head and velocity head are both increasing. O The pressure head is decreasing and the velocity head is constant. O The pressure head and velocity head are both decreasing. P Type here to search 0022 10°C Sunny AG A Q0 ENG 16/02/2022 DELL Esc F6 FB num 2 4€ E R Y F G J K ck D %23 B N M end V page page up ctri alt gr alt
Parvinbhai
I ll rate
Three pipes are connected in series with properties given as: for pipe A, L= 300 m, diameter = 15 cm, for pipe B, L= 400 m, diameter= 20 cm and for pipe C, L= 600 m, diameter= 25 cm. The Manninbg's coefficient of the three pipes n= 0.011. If the total frictional losses is 5 m, excluding minor losses, determine the amount of water flowing through the pipe system. (WITH FREE BODY) CHOICES: a.30 L/s b.35 L/s c.25 L/s d.20 L/s
The liquid storage tank shown in Fig has two inlet streams with mass flow rates w1 and w2 and an exit stream withflow rate w3. The cylindrical tank is 2.5 m tall and 2 m in diam-eter. The liquid has a density of 800 kg/m. Normal operating procedure is to fill the tank until the liquid level reaches a nom-inal value of 1.75 m using constant flow rates:w1=120 kg/min, w2=100 kg/min, and w3=200 kg/min. At that point, inlet low rate w1 is adjusted so that the level remains constant.However, on this particular day, corrosion of the tank has opened up a hole in the wall at a height of 1 m, producing a leak whose volumetric flow rate q4(m3/min) can be approximated by q4=0.025√h−1 where h is height in meters.(a)If the tank was initially empty, how long did it take for theliquid level to reach the corrosion point?(b)If mass flow rates w1,w2,and w3 are kept constant indefi-nitely, will the tank eventually overflow? Justify your answer.
Water flows through a measuring nozzle of 40mm diameter in a pipe of 75mm in diameter at a flow rate of 0.015 m3/s. Determine the pressure difference through the nozzle if the temperature is (a) 10°C, (b) 80°C.
In the diesel oil transfer facility (ρ rel = 0.85), from the storage tank to the consumption tank, we want to install a pump to circulate a flow of 45 lt / s. The 400m long pipe is cast 150mm in diameter and consists of a check valve, a gate valve and 2 commercial medium radius elbows. The consumption tank is pressurized to 3.8 bar of manometric pressure. Determine the drive power of the pump in kW if its performance is 68%. Additional data, load loss factors: 1. Check valve Kr = 1.5 2. Gate valve open Kv = 0.21 3. Commercial elbow of mean radius Kc = 0.75, for each elbow 4. Storage tank outlet sharp angles Ks = 0.5 5. Entrance to consumption tank Ke = 1 6. Pipe friction factor f = 0.025