2.Complete the following table related to sieve analysis:Sieve sizeCumulative Mass retained (g)Mass retained on sieve (g)%RetainedCumulative % passing37.528112013144710726.311651763.3531625761.180.685112660.42515410.317110.2118810.15201121460.075Pan2346

Given: Sieve size Cumulative Mass retained (g) Mass retained on sieve (g) %retained Cumulative %…

Answered: 2.Complete the following table related…

Engineering

Civil Engineering

2.Complete the following table related to sieve analysis:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Below is a sieve analysis for a fine aggregate. a. Complete the sieve analysis to get percent…

Q: Differentiate and discuss the common hardness testing methods

A: Hardness testing: - It is defined as a non-destructive test method which is used to determine…

Q: The following table shows the results obtained from Wash Test done on samples of fine aggregates.…

Q: Q1) Students are checking hardness of a mineral in laboratory, and they found that specified mineral…

A: Hardness- It is the property of a material to resist scratch on its surface. It can be determined by…

Q: Following are the results of a sieve analysis. Determine: a. Cu b. Cc c. So Sieve No. 4 6 10 20 40…

A: Sieve analysis is a method used for determining the particle size distribution of a coarse grained…

Q: Weight Retained 1.570 kg 1.554 kg 2.570 kg 1.84 kg 2.223 kg 0.22 kg 0.023 kg Sieve No. Cum. Weight…

Q: The mass of a bulk density bucket is measured as 21XY g when it is empty. (Where XY are the last two…

A: Bulk Density of aggregate: The Bulk density of aggregate also known as Unit weight of an aggregate…

Q: please help us in this data table please help to fill it up but if possible the most important is…

A: The grain size distribution of the soil sample can be performed by Sieve analysis Dry sieve…

Q: 4. The percentage of fine aggregate 5. The percentage of filler material

A: 4. Fine aggregate range lies from 4.75mm to 0.075mm. Hence from the table: % Fine aggregate = 65-3 =…

Q: write small introduction about (cement, fine aggregate, coarse aggregate ) also about superplstizer…

A: Cement is a binding substance used for building, and civil engineering construction works. Cement is…

Q: Problem statement: Give a brief explanation about Lime, types of lime and various impurities in lime

Q: What is the maximum diameter of aggregate considering the depth of the slab in cm if the value of d…

A: This question is related to the design of RCC Structure.

Q: V. DATA AND TABULATION 1. Depending upon the form of the specifications for use of the material…

A: Given data:

Q: Given the % Cum Pass made on a fine aggregates: Sieve size mm 9.5 4.75 2.36 1.18 0.6 0.3 0.15 %…

A: It is required to determine the % cumulative retained. % Cumulative retained=100-% cumulative…

Q: For computational purposes, provide virtual Data for the following term and compute for the Bulk…

A: Given Weight of bucket filled with dry coarse aggregate =2.68 kg

Q: If the time started performing the final setting time of cement is 7:34:39 am and the time of final…

A: Setting Time is the time elapsed between the starting of the test and the time of final setting.…

Q: Define the minimum weight of fine aggregate for sieve analysis as per ASTM C136 ?

A: ASTM C136, 2006 Edition, February 15,2006 - Standard Test Method for sieve analysis of Fine and…

Q: 1. Show how actual strength compared with design strength by plotting the published column strength…

A: Solution: Column curve: Column or strut is a compression member, the effective length of which…

Q: results shown in the Table below, Calculate the percent passing through each sieve. Plot percent…

A: Calculate the percentage of soil retained over each sieve, % retained = Weight of soil…

Q: Calculate the weight of cement, fine aggregate (sand), coarse aggregate (rock) and gallons of water…

A: Given Data: pad dimensions=5ft×5ft×5inmix=1:2:4w/c=0.50 The maximum coarse aggregate size as per…

Q: What is a Test Sieve? What is a Test Sieve used for? What are the types of Test Sieves? What are the…

Q: Describe the sieve analysis.

A: A sieve analysis is an analytical method that is used to define the particle size distribution of…

Q: in the table based on the information that has been given Us Standard Sieve No. Sieve Opening (mm)…

Q: The strength of bricks were monitored and recorded. The table below provides the recorded data for…

A: Brickwork : Brick masonry is a durable construction material. It is built by systematically laying…

Q: Note: For computational purposes, provide virtual Data for the following term and compute for the…

A: We are asked to find out Bulk Unit weight and Percentage voids of the fine aggregate. Bulk specific…

Q: Note: For computational purposes, provide virtual Data for the following term and compute for the…

Q: Mass of Aggregate (kg) 8.70 Volume of Mold (cum) 0.00556 Unit Mass (kg/m³) Unit Weight (kN/m³)…

Q: sieve analysis what's the meaning or gonna happen if the So is zero

A: A sieve test is generally called as gradation test, is one of the most important and widely used…

Q: What is the cumulative percent retained on the sieve with the lowest percent retained?

A: We will directly write average of all three trials in table and find cumulative percent retained.

Q: Explain the specifications of tamping rod used in cube filling for cube test ?

A: Tamping rods are used for strengthening of concrete which is mixed freshly in tests for slump, air…

Q: A sieve analysis test was performed on a sample of coarse aggregate and pro- duced the results in…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: 1. Given the results of an Atterberg limit test. Complete the test report which will include filling…

Q: Differentiate porosity, permeabiloity, water saturation and resistivity properties. What…

A: Solution: Porosity: It is defined as the property of loose sediments, rocks, or soil to hold fluid…

Q: Write water absorption of Aggregate: 1-Introduction. 2-Procedure. 3- discussion .

A: Introduction - Water absorption of aggregate - it is used to understand the difference of apparent…

Q: A. A materials engineer conduct a Moisture Content Test. Here is the result Oven dry Sample (2DD +…

Q: Weight of Sieve with Sieve no. Weight of Empty Weight Retained Aggregates Sieve (grams) (grams)…

A: Given Seive No. Weight of empty seive, Weight of seive with aggregate, To Determine Weight retained…

Q: Q5 - HomeWork/ Calculate how much Water and Bentonite are required to make 800 bbl of 10.5 ppg, then…

A: Given: 800 barrels of 10.5 lb/gal water based drilling mud.

Q: Sieve Size 3/4 in. (19 mm) 3/8 in. (9.5 mm) No. 4 (4.25 mm) No. 10 (2 mm) No. 40 (0.425 mm) No. 200…

A: Given, To determine, the suitable ratio for blending aggregates A and B to obtain an acceptable…

Q: Calculate the individual quantity of cement, sand, gravel, and water for the concrete pedestal shown…

Q: ive a discussion of theory for the topic "consistency of standard cement paste" (en

A: CONSISTENCY OF STANDARD CEMENT PASTE:- INTRODUCTION:- →As per IS: 4031 (part4)-1988:- Standard…

Concept explainers

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.

Question

2.Complete the following table related to sieve analysis:
Sieve size
Cumulative Mass retained (g)
Mass retained on sieve (g)
%Retained
Cumulative % passing
37.5
28
11
20
13
14
47
10
72
6.3
116
5
176
3.35
316
2
576
1.18
0.6
851
1266
0.425
1541
0.3
1711
0.21
1881
0.15
2011
2146
0.075
Pan
2346

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2: Mass retained on sieve (g)

VIEW

Step 3: % retained

VIEW

Step 4Cumulative % passing

VIEW

Step 5: Final complete table

VIEW

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Void Content—Calculate the void content in the aggregate using the bulk densitydetermined by either the rodding, jigging or shoveling procedure, as follows:
For this problem, I need help understanding the data I am supposed to use to graph the needed graphs for this question and how these graphs are supposed to look.
List some Clay minerals and their uses.
if total sample mass of aggregate is 164.9 grams, then the percent passing from sieve size #30 only is equal to ………………
Using online resources, find the aggregate specifications for the state of California and identify the limitations for deleterious materials in aggregates used for asphalt concrete
If the specimen is originally square and has dimensions of a = 4 in., b = 3 in., and a thickness of t = 0.4 in., determine its new dimension a' after the load is applied. Express your answer to six significant figures and include appropriate units. a' = 4.00737 μA Submit Previous Answers Request Answer Part B X Incorrect; Try Again; 5 attempts remaining 0 in Determine its new dimension b' after the load is applied. Express your answer to six significant figures and include appropriate units. μᾶ b= 3.00333 ? in Submit Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining
3 - What a hardness test can show. What kind of test can hardness test replace?
A small amount of resin weighing 4.56g occupies a height of a 10-ml graduated cylinder equivalent to one ml. One mL of water was added and the level was read at 1.7 mL. Estimate the porosity of the resin.
1. summarize the definition of the following items and give the formula. ① Specific surface area; ② Porosity; ③ Saturation and ④permeability
Situation 1. From the given data of materials retained between consecutive sieves, compute the value of fineness modulus