V. DATA AND TABULATION 1. Depending upon the form of the specifications for use of the material under test, the report shall include the following: 1.1. Total percentage of material passing each sieve, or 1.2. Total percentage of material retained oneach sieve, or 1.3. Percentage ofmaterial retained between consecutive sieves. 2. Report percentages to the nearest wholenumber, except if the percentage passing the 75-um (No. 200) sieveis less than 10 %, it shall be reported to the nearest 0.1%. 3. Report the fineness modulus, when required, to the nearest 0.01. CUMULATIVE CUMULATIVE SIEV AMOUNT AMOUNT PERCENT PERCENT RETAINED, g (b) RETAINED, 9 (a) RETAINED, (c)=(b)*100/TÓT E PASSING SIZ (d)=100 - (c) AL 1% 215 885 3/4 980 1/2 2350 3/8 1190 4. 2205 1985 10 1840 40 1650 100 980 200 660 PAN 60 15000 ТОTAL [7]

V. DATA AND TABULATION 1. Depending upon the form of the specifications for use of the material under test, the report shall include the following: 1.1. Total percentage of material passing each sieve, or 1.2. Total percentage of material retained oneach sieve, or 1.3. Percentage ofmaterial retained between consecutive sieves. 2. Report percentages to the nearest wholenumber, except if the percentage passing the 75-um (No. 200) sieveis less than 10 %, it shall be reported to the nearest 0.1%. 3. Report the fineness modulus, when required, to the nearest 0.01. CUMULATIVE CUMULATIVE SIEV AMOUNT AMOUNT PERCENT PERCENT RETAINED, g (b) RETAINED, 9 (a) RETAINED, (c)=(b)*100/TÓT E PASSING SIZ (d)=100 - (c) AL 1% 215 885 3/4 980 1/2 2350 3/8 1190 4. 2205 1985 10 1840 40 1650 100 980 200 660 PAN 60 15000 ТОTAL [7]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Explain the effect of fine content and plasticity on liquefaction resistance.

A: Fine Content : Fine content is defined as the percentage of soil particles that are smaller than…

Q: 2. Three samples of aggregates are sieved to obtain the grading curve. A set of different sieves is…

A: Three samples of aggregates are given:-Sieve sizeMass of sieve (g)Mass of sieve+aggregates…

Q: A 1775g of coarse aggregates was soaked for at least 24hours prior to the lab. It is then brought to…

Q: Use AASHTO method to classify the following different group indices based on their test results. 1)…

Q: (c) Asphalt concrete mixture of AC 14 will be used to construct the wearing course layer. The coarse…

Q: Why a reduction factor ra is used in liquefaction relationship? Please explain with sketches.

A: To explain:Why reduction factor rd is used in liquefaction relationship

Q: Table shows the grain size distribution for two aggregates and the specification limits for an…

A: Let's try with 50:50 blend: Trial 1: Blend gradation of aggregate A and B can be calculated using…

Q: Aggregate from two stockpiles, A and B having coarse aggregate angularity (crushed faces) of 55% and…

A: given values x1=55% x2=75%P1=45P2=55p1=30%p2=60%

Concept explainers

Mechanical Processes

In civil engineering, the materials have to undergo a series of manufacturing processes before using them in construction and structural applications. These manufacturing processes form the foundation stone of mechanical processes. Some of the civil engineering materials such as bars, metallic beams, metallic columns, surveying equipment, earthmovers, overhead cranes, structural and construction components, and even cement that is the most fundamental construction component need to undergo different manufacturing processes before they are ready to use. These processes are mechanical.

Question

V.
DATA AND TABULATION
1. Depending upon the form of the specifications for use of the material under test, the
report shall include the following:
1.1. Total percentage of material passing each sieve, or
1.2. Total percentage of material retained oneach sieve,
or
1.3. Percentage ofmaterial retained between consecutive sieves.
2. Report percentages to the nearest wholenumber, except if the percentage passing the
75-um (No. 200) sieveis less than 10 %, it shall be reported to the nearest 0.1%.
3. Report the fineness modulus, when required, to the nearest 0.01.
CUMULATIVE
CUMULATIVE
SIEV
AMOUNT
AMOUNT
PERCENT
PERCENT
RETAINED, g (b)
RETAINED, 9
(a)
RETAINED,
(c)=(b)*100/TÓT
E
PASSING
SIZ
(d)=100 - (c)
AL
1%
215
885
3/4
980
1/2
2350
3/8
1190
4.
2205
1985
10
1840
40
1650
100
980
200
660
PAN
60
15000
ТОTAL
[7]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Students in the materials lab performed the specific gravity test and bulk unit weight and voids of aggregate on a sample of coarse aggregate and obtained the following data: Mass of oven dried aggregate: 1042 g Mass of aggregate submerged in water: 646 g Mass of saturated surface dry aggregate: 1058 g Bulk dry specific gravity of aggregate. Find the absorption of aggregate. If the dry rodded unit weight of aggregate found to be 1695 kg/m3 , calculate the percent voids between aggregate particles in this test. We blend this aggregate with other aggregate with bulk dry specific gravities of 2.23. Calculate the bulk dry specific gravity of the blend if the blend proportion is 40:60.
Quartering (or splitting) means reducing sample sizes into reasonable volumes. Would you expect every after each quartering (or splitting) process, the weight of the original aggregates would be reduced to half or almost half? Why or why not? Defend your reason.
Us Standard Sieve No. Sieve Opening (mm) Weight Retained (g) % Retained on Sieve % Passing Sieve 4 4.75 12.7 6.2 93.8 10 2 24.8 12.1 81.7 20 0.85 21.5 10.48 71.24 40 0.425 38.8 18.92 52.33 60 0.25 23.8 11.60 40.73 100 0.15 19.5 9.51 31.23 200 0.074 46.7 22.76 7.463 Minus 200 17.3 8.44 0 Total 205.1 for D10 and D60 calculate the k value utalizing Hazen's approxoimation. c=100
5.20 Calculate the sieve analysis shown in Table P5.20, and plot on a 0.45 power gra- dation chart. What is the maximum size? What is the nominal maximum size? TABLE P5.20 Sieve Size 37.5 mm 25 mm 19 mm 9.5 mm 4.75 mm 0.60 mm 0.075 mm Pan Amount Retained, g 0 315 782 1493 677 1046 1502 45 Cumulative Amount Retained, g Cumulative Percent Percent Passing Retained
help me find solutions for a,b,c,d,and e
i need the answer quickly