2.71 An air-conditioner system consists of a spray section followed by a reheater. Moist air at 30°C and o = 75% enters the system and passes through a water spray, leaving the spray section cooled and saturated with water. The moist air is then = 44% with no change in the amount heated to 24°C and & of water vapor present. For operation at steady state, determine 10od lo om odi () (a) the temperature of the moist air leaving the spray section, in °C. (b) the change in the amount of water vapor contained in the moist air passing through the system, in kg per kg of dry air. Locate the principal states on a psychrometric chart.

Q: What are fluidised or moving-bed adsorbers?

A: Adsorption is a separation process in which the solute from the fluid is separated by adsorbing on…

Q: Use equations and words to describe how stirring a solution will affect the mass-transport limited…

A: The current that flows through a solution at any time is a direct measure of the rate of the…

Q: Is pinch point always located at the feed stage?

A: The location of the pinch point is to be mentioned.

Q: Mention some key considerations during installation of a cyclone seperator?

A: Cyclonic separation is a means of separating different liquid phases, or, separating particles from…

Q: Explain RECYCLE AND BYPASS?

A: To design a new process or analyze the existing one, material balance, energy balance equations at…

Q: Illustrate and discuss the process flow for the manufacture of porcelain

A: Solution-Step:  (a) Component needed(i) Feldspars K2O.Al2O3.6SiO2 & Na2O.Al2O3.6SiO2(ii) Quartz…

Q: Describe five main parameters that govern the performance of the polymer production process. Provide…

A: Polymer manufacture is a complex process governed by numerous aspects that affect the final…

Q: Describe 1st angle and 3rd angle Projections?

A: 1. First Angle Projection : In the first angle projection, we can placed the object in the 1st…

Q: In the plate and frame filter press, by plotting the filtrate volume as a function of time per…

A:

Q: Process flow scheme on how to make tempered glass

A: There are two types of commercial glass based on the process of their manufacture. These are:…

Q: Mention the steps that are helpful in performing material and energy balance calculations.

A: Material and energy balance make up the basic of any chemical engineering plant. Material balance…

Q: The knowledge of chemical Engineering is essential to ensure the normal operation in most…

A: Chemical engineering basically involves the production with the help of raw materials and…

Q: Can you explain the stained glass process?

A: The stained glass means colored glass as a material and to works formed from it. The term stained…

Q: How to manufacture ball bearing and what manufacturing processes are involved in manufacturing of…

A: A bearing machine element that enables rotational or linear movement, and reduces friction between…

Q: Create a solver or calculator using MS Excel utilizing different application on Chemical…

A:

Q: Explain the friction between the mater (soled with soled, liquid with liquid)?

A: Motion: Motion is the phenomenon in which an object changes its position over time. Motion is…

Q: Differentiate between Unit operations and Unit process in Chemical processing

A: Unit operationsThis term is used in Chemical processing which is defined as the operations in which…

Q: When we change the fluid package from one package to another, does the temperature and pressure…

A: When we change the fluid package from one another then the following properties will change such…

Q: What are the advantages of the espresso machine over the drip method?

A: The advantages of the espresso machine in comparison to the drip method are to be mentioned.

Q: List out various tests for the measurement of workability and explain any 2 in detail.

A: The objective of the question is to list out the various tests used for measuring workability in…

Q: How to calculate pressure drop in Gas pipe , formula ,

A: When gas flows in pipes, the pressure drop is caused due to following reasons:Friction in the…

Q: 3 Ways to separate pebbles and water and its step by step process

A: The three methods that can be used to separate water and pebbles are as follows: 1) Pour the mixture…

Q: Describe the factors that affect fluidization.

A: Factor that have an effect on fluidization are  fluidization parameter (calculated through inlet air…

Q: Discuss and differentiate the different methods of carrying out a distillation process.

A: Introduction Distillation is the process of separating  the components or substances from a liquid…

Q: Explain and describe possible factors that may affect fluidization.

A: Fluidization parameter (calculated via inlet air drift fee and rotor speed), stress distinction over…

Q: Discuss Lever-Operated Knapsack Sprayer

A:

Q: What are centrifugal pumps?

A: Pump: Pump is a mechanical device which is widely used in chemical industry to transport of fluid…

Q: What equipment is included in a typical distillation operation?

A: The different types of equipment included in the distillation operation is to be mentioned.

Q: can you present your working in full

A: The volumetric flow rate (q) through a triangular tunnel depends on height (h), width (w) and the…

Q: draw process flow diagram for amino acid industry

A: Introduction Amino acids are manufactured by a set of biochemical  processes , or metabolic…

Q: Describe about the Electro-osmosis.

A: The electro-osmosis is to be described.

Q: Draw the steam distillation apparatus and indicate the names of the each part of the apparatus

A: Steam distillation is a separation process used to separate organic compounds by using the thermal…

Q: Define about the Seismic Refraction Survey ? Why it is useful ?

A: The Seismic Refraction Survey is to be defined and it is to be shown how it is useful.

Q: What is the method or heory that the laborator device depends on in measuring potassium?

A:

Q: Explain two examples of crystallization processes applied in the industries

A: All salts dissolve in the solution according to their solubility in the given solvent. At the given…

Q: what applications does packed column have?

A: Packed columns are commonly used in various industries for separating, purifying, or removing…

Q: Provide a matrix of cradle-to-grave analysis diagram of cosmetic products by a chemical engineer.

A:

Q: Identify various factors affecting workability

A: The objective of the question is to identify the various factors that affect the workability of a…

Q: Does the Underwood equation compute internal or external reflux?

A: The type of reflux calculated by the Underwood equation is to be calculated.

Q: What is meant by a pinch point?

A: The meaning of the pinch point is to be mentioned.

Steady State Model

The steady-state model typically states that the entire universe is always enlarging, although it balances a fixed average density and matter that is being constantly generated to make new galaxies, star forms at a similar rate that the previous ones get indistinguishable due to the growing range and velocity of recession.