2.51 Water, oil, and salt water fill a tube as shown in Fig. P2.51. Determine the pressure at point 1 (inside the closed tube). Oil density -1.20 slugs/t -1-In. diameter -2-in. diameter 3 't Salt water, SG - 1.20 2't 4 ft Water I Flgure P2.51

2.51 Water, oil, and salt water fill a tube as shown in Fig. P2.51. Determine the pressure at point 1 (inside the closed tube). Oil density -1.20 slugs/t -1-In. diameter -2-in. diameter 3 't Salt water, SG - 1.20 2't 4 ft Water I Flgure P2.51

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

15. If the pressure in pipe A is 6 kPa, the SG = 0.85 pressure in pipe B =. ........... psig. Water 90 mm 30% a. 1.27 70 mm b. 8.73 40 mm C. 60.17 SG = 13.6 Mercury d. None of all these
An open tube is attached to a tank as shown. A). If Liquid X (Oil SG=0.55) rises to a height of 800 mm in the tube, what is the pressure Pa (in kPa) of the air above water? Neglect capillary effects in the tube. B). If Liquid X (Alcohol SG=0.79) rises to a height of 800 mm in the tube, what is the pressure Pb (in kPa) of the air above water? Neglect capillary effects in the tube.
Hemispherical dome - SG = 0.8 4 m 60 kPa 3 m 3 m Water 2 m B
3. [Ch4 - 1] What is the head loss and corresponding pressure drop (in units of bars) across a 30- mm-wide open gate valve when oil (SG = 0.90) flows through at a rate of 4 x 10-3 m/s? 4. [Ch4 – 2] Oil (SG = 0.80, v = 10- m/s) flows at a rate of 2 x 10-3 m'/s through a 20-mm- diameter commercial steel pipe. What is the equivalent length of a 20-mm-half open gate valve placed in the line?
PROBLEM 3: For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids-castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (1llustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z = 7m. 1m hinge Linseed Oil (SG = 0.938) Castor Oil (SG = 0.96) 10 m 2 m water The hydrostatic force due to linseed oil F1.
1- Water flows through a horizontal pipe at a rate of 9.1 L/s. The pipe consists of two sections of diameters 10.16 cm and 5.08 cm with a smooth reducing section. The pressure difference between the two pipe sections is measured by a mercury manometer. Neglecting frictional effects, (a) determine the differential height of mercury between the two pipe sections. (b) How would the reading change if the manometer on the 2in pipe is replaced by a pitot tube? 10.16 5.08 h
The initial pressures at A and B are the same at 109 kPa. If the pressure at the liquid at A (SG1 = 2.65) is increased to 134 kPa while keeping the pressure at B constant, determine the new position (Ah, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.69 cm., and the inclination of the tube is 16° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places. SG B Air Yı Δh Ah Mercury
The initial pressures at A and B are the same at 105 kPa. If the pressure at the liquid at A (SG1 = 1.96) is increased to 132 kPa while keeping the pressure at B constant, determine the new position (Δh, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.58 cm., and the inclination of the tube is 11° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places.
5-64. A thin rubber tube of 25 mm inside diameter is used to siphon water from the large tank of Figure 5.56. To prevent the tube from collapsing, the pressure inside the tube can not be less than 50% of the pressure outside the tube. Determine the smallest value of h to prevent the siphon from stopping due to collapsing of the tube. 2.5 m 5 m Figure 5.56 System for Exercise 5-64. THANK SUNTETICE Full Michifo Nas s itset SCH
English (United States) Oil at 80°C (p = 56.8 lbm/ft³ and μ = 0.00278 lbm/ft*s) is flowing steadily in a 0.5-in-diameter, 120-ft-long-pipe. During the flow, the pressure at the pipe inlet and exit is measured to be 120 psi and 14 psi, respectively. Determine the volumetric flow rate of oil through the pipe assuming the pipe is inclined 20° downward. Accessibility: Investigate X TO
5.13 A horizontal cylindrical tank given in Fig.P.5.13 is filled with water and oil in two different densities. Calculate and plot changes in pressure on the cylindrical surface of the tank. (Hint: Hydrostatic pressure of the oil phase at the top affects the water phase at water-oil interface. In addition, hydrostatic pressure of water phase should also be considered). Tank Dimensions: Diameter : 0.80 m : 2.40 m Length Height of interface : 0.78 m 0.8m Liquids: (1) -(2)* Oil : p= 890 kg/m³ μ-12 cP Water: p= 1000 kg/m³ Figure P.5.13 µ=1 cP