2.5 kN Calculate the bar force members IJ, ID, LK and BC using method of section. 2 kN 2 kN K 2 KN 2 kN 6 m 1 kN 1 kN ANS: IJ = 4.6 kN (C) ID = 2.24 kN (C) LK =6 kN (C) BC = 5.25 kN (T) A B 2 m 2 m 2 m 2 m- -2 m +2 m

2.5 kN Calculate the bar force members IJ, ID, LK and BC using method of section. 2 kN 2 kN K 2 KN 2 kN 6 m 1 kN 1 kN ANS: IJ = 4.6 kN (C) ID = 2.24 kN (C) LK =6 kN (C) BC = 5.25 kN (T) A B 2 m 2 m 2 m 2 m- -2 m +2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A solid steel shaft supports loads PA=490 N and PD = 400 N, as shown. Assume L₁ = 180 mm, L₂ = 620…

Q: If the allowable bearing stress for the material under the supports at A and B is = 830 psi,…

Q: Determine the shear force 5.67 ft to the right of point A for the beam shown belowif P = 843 lb, W =…

Q: Reqd: Determine Maximum Shearing Stresses for the 3 segments and Oat C (2)Solid 60-mm-diameter G =…

Q: 0.1: By using LRFD method: A. Determine the max. load (P) can be applied on the structure shown in…

A: The specifications are: The area of the plate=Ag=2*(1*20)=40 in2 The diameter of bolt=7/8 in The…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: For the beam shown, 3V a. draw SFD and BMD, b. prove that for the isosceles, Tmax. = bh C. if Ball =…

Q: number of significant digits; the tolerance is +_1 in the third significant digit

A: Step 1: At joint C, the forces are FCE,FCD and the external Load of 5.5kNSum of forces in y…

Q: If P= 8.571 kN, Determine the stress in member CE assuming that the area in steel is 24 mm2.Show

A: Step: 1 Truss: - It is a pin jointed frame where bending moment does not exist in member only carry…

Q: QUESTION 1 Determine the force in member DF using method of section of the Howe truss shown if: P=…

Q: Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: For the truss shown, the wooden AB bar has solid cireular cross-section with diameter d and the…

A: Given information: Here, P = 75 kN Length of AB, L = 2 m F.O.S, n = 2.5 E = 10 GPa Tetmajer’s…

Q: Show complete solution (show how you achieve the member forces , e.g method of joints/method of…

A: Given : 2D truss solve using consistent deformation EI = constant

Q: CE A 1.5 m- Wo = 8 kN/m P₁ = 20 KN -1.5 m- D P₂ = 6 KN B -1 m1 m E

Q: .

A: As there are multiple questions posted, according to the guidelines only the first three subparts…

Q: Determine the force of member GA. Include a negative sign if the answer is in compression.

Q: Determine the vertical displacement of joint A. Each A992 steel member has a cross-sectional area of…

A: Given :- A truss is given with each A992 steel member has a cross-sectional area of 400 mm2 Point…

Q: What does the variables stand for and assumption is valid ?

A: Stress strain diagram for singly reinforced beam

Q: Determine the forces in members DE and DL. The forces are positive if in tension, negative if in…

Q: Solve the following problem and show your complete solutions. Explain your answer for better…

A: Given Load 2.7, 4.5 and 1.8 kNSpan 12 mTo find out Member forces

Q: In order to reinforced a column in an existing structure, two channels are welded to the column as…

A: Given: Section: W 12 x 50 C 6 x 13 Effective length of the column, KL=4.9 m Fy = 350 MPa Fu = 450…

Q: Determine the force in member FE of the truss below. Indicate as positive if the member is in…

Q: a. Determine the maximum flexural stress b. If the nails shown in the cross-section can each support…

Q: A Bar JK uniformly weighing 34 kN ln is being supported by Strut MN and a hinge at J Consider these…

Q: Calculate the forces in members BE and BD of the loaded truss. The forces are positive if in…

Q: E 6 m B 4 m 4 m 4 m P1 P2

A: Finding out member forces.

Q: bkN D. 7777 em e m

A: As there are multiple questions posted, only the first three subparts are being answered. Kindly…

Q: A SHAFT OF TO RIGID SUPPORTS SEGMENT AC, AND LO. FOR BRONZE 6= 35 and FIK STEEL, 6 = 83 6Pa Shearing…

Q: Solve the truss shown in figure 02 below for member forces using any method of your choice.

A: to find - forces in members

Q: Problem 4.- Determine the force in member BE of the loaded truss and whether the member is in…

A: Given:- Forces:- 6kN.5kN,4kNTo find:-Force in member BE

Q: Calculate the member forces of the loaded structure.

A: According to given data Calculate the member forces of the loaded structure. Given load 60 KN , 40…

Q: Given: E 73 GPa b 3D 25.4 тт h3 3. 18 mт P = m = 100 g L 50 тm 6PL Beam Equation: axial strain = ɛ =…

Q: 50 lb-ft T2 (1) 30 lb-ft A (3) B C D Assume for the above sketch that the shaft is restrained from…

Q: 1. The truss has 5 equilateral triangles. 3m on a side (all vertex angles are 60°). With the given…

A: Given data All vertex angles = 60° Find force in each members and it type (nature of member either…

Q: A stepped vertical steel bar ABCD is fixed at the top end A. Each segment of the bar AB, BC and CD…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: B 4.5m 主 P2 3. 4m 1.5 m 2.8nH.5m Find the forces in all members of the muss Shown in the figure ·…

Q: Construct the V and M diagram of the beam loaded as shown. Answer: Max. Moment = 40 KN 20 kN/m 50 KN…

Q: 800lb 60 12' 12 FORCE Ibs A MA= Fxd Couples F= F.Cos( e ) F= F.Sin( e) Forces 100lb/ft

A: Given data Point load and UDL Length of span.

Q: a) Determine the force in member BG of the truss. b) Determine the force in member CD of the…

Q: ВотTом СНORD: E=200GPA, A=1000SQMM OTHER MEMBERS: E=70GPA, A=1200SQMM ANALYZE THE TRUSS USING…

A: External SI = R-r = 0Internal SI = (m+r)-2j =1 Taking AD as redundant

Q: a. Axial force on member marked with a in kN. b. Axial force on member marked with b in kN.

A: Axial Force in member a is 10.2 KN

Q: Q3 h nɔd. For the truss shown, the wooden AB bar has solid circular cross-section with diameter d…

A: Given that; L=2m P=75KN n=2.5 E=10GPa λ<λcr=100, d=?Tetmayer's Formula;σcr=(28.73-0.19d)MPa

Q: 25 P₁ 45 P2 B () 45 P2 25 P₁ 45 P2 D M E 6 panels @ 3.0 m = 18.0 m 43 P₂ 25 P₁ 6.0 m

Q: 8 kN 2 m 2 m 2 m A 14 kN B 6 kN C DI RDH = 28 kN-m 12 kN-m RA = Rov ='

Q: 6

A: Step 1: Step 2: Step 3: Step 4:

Question

2.5 kN
Calculate the bar force members IJ, ID,
LK and BC using method of section.
2 kN
2 kN
K
2 KN
2 kN
6 m
1 kN
1 kN
ANS: IJ = 4.6 kN (C)
ID = 2.24 kN (C)
LK =6 kN (C)
BC = 5.25 kN (T)
A
B
D
F
2 m
-2 m -2 m
2 m-
-2 m
2 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the shear stress occurring at point D.
,,
Determine the forces in members BE and CE of the loaded truss. The forces are positive if in tension, negative if in compression.Help me to get correct answer.
For the truss shown below determine the vertical displacement at joint b. Assume A = 0.15 in², E = 29,000 ksi
1) 5@3m = 15 m Hg 1 kN Determine the support reactions and member forces of GF, EF, GE, HG, HD, GD and HI. The method of joints is selected to solve the problem. VK E 5 m 15 B 2 kN 2 kN НА 2 kN VA 6 15 = 6 5 5 HD: ? ? = 2m [VK = OkN, VA = 7kN (†), Hg = 9.6kN (-), HA = 9.6kN (→)]
Situation 13 - Using method of sections, determine the internal force of members 3-6 and 5-7. Use L = 2 m and P = 3 kN. 2P P 3P 1² M 45° 45° 3 L L 45° →→X
The pin support A and roller support B of the bridge truss are supported on the concrete abutments. If the square bearing plates at C and D are 20 inches x 20 inches, and the bearing failure for concrete is (?????)? =3.8 ???, determine the factor of safety against bearing failure for the concrete under each plate.
Q.1: By using LRFD method: A. Determine the max. load (P) can be applied on the structure shown in Figure, neglect block shear. B. Depends on channel section, find channel size (C9) that can be used as shown in Figure assume Pu=600 kips. 2PL(1*20)in 3*5in=15in dpoit P A36 for PL A572-Grade 50 for Channel 2C=?
Determine the force in each member of the truss shown. Use a=1m, b=3.1m and P= 10 kN. Box your final answers. 4@4m=16m P 18 kN B a 5m 6m G 5m 27 kN 36 KN
Really need please. New solution if possible.
Solve all 4 parts otherwise don't
A: Without any solutions, identify the zero-force members. B: Determine the forces in the members identified by "x" using two sections ONLY. 70 KN S0 KN 50 KN 6 m 14 m= 16 m