B2. The pendulum consists of a 5-kg thincylinder fixed to a 0.6 m long rod with amass of 2-kg. e 0.80. The pendulum isreleased from rest when eDetermine the maximum angle of rebound- 90°.after the cylinder strikes the floor.0.09 m0.6m0.09 m

Given: m1=5 kgL=0.6 mm2=2 kge=0.8θ=90 To find: maximum angle of rebound

2. The pendulum consists of a 5-kg thin cylinder fixed to a 0.6 m long rod with a mass of 2-kg. e=0.80. The pendulum is released from rest when 8 Determine the maximum angle of rebound after the cylinder strikes the floor. 90°

2. The pendulum consists of a 5-kg thin cylinder fixed to a 0.6 m long rod with a mass of 2-kg. e=0.80. The pendulum is released from rest when 8 Determine the maximum angle of rebound after the cylinder strikes the floor. 90°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A cable connects the center of cylinder A (diameter = 0.8m) to the hub of cylinder B as shown below.…

Q: The force F, is applied to a rope which wraps around a hip with a radius of 200 mm. The disk has a…

A: For the solution refer below images.

Q: The 52-kg reel has a radius of gyration about its center O of ko = 240 mm. If it is released from…

Q: If the 250-lb block is relcased from rest when the spring is unstretched, determine the velocity of…

Q: Part A The 30-kg disk is originally at rest, and the spring is unstretched. A couple moment M = 86…

A: Find the distance travelled by the disk.

Q: The 46-kg cylinder has an angular velocity of w = 34 rad/s when it is brought into contact with the…

A: The time required to stop spinning the cylinder and the force in the link AB. Given: The mass of the…

Q: each of 0.15 m radius and 1.9 kg mass). If the system is released from rest when 0= 76°, when rod AB…

Q: A 256-b block is released from rest when the spring is unstretched. The drum has a weight of 76 Ib…

Q: The 30-lb collar A begins at rest in the position shown. Under the influence of a constant 50-lb…

Q: The double pulley consists of two wheels which are attached to one another and turn at the same…

Q: Figure 150 mm. 75 mm 1 of 1 P = 150 N ▼ Part A If the cord is subjected to a horizontal force of P =…

Q: H.W.02: The automobile has a mass of 2 Mg and center of mass at G. Determine the towing force F…

A: Apply the conditions of equilibirum ∑Fx=0FB-Fcos30°=0…

Q: The 28-kg wheel is rolling under the constant moment of M = 84 N.m. The wheel has radius r = 0.53 m,…

Q: B 1 m Ө A

Q: The system is at rest with the spring unstretched when 8 = 0. The 5.3-kg uniform slender bar is then…

A: mass,m=5.3 kgb=0.45 mto determine:(a) Spring constant k(b)magnitude of angular velocity

Q: The wheel is made from a 5-kg thin ring and two 2-kg slender rods. If the torsional spring attached…

A: According to the given information, we have the mass of the wheel is 5kg thin ring and 2 kg slender…

Q: A 80 mm X 250 mm 400 mm 80 mm B - Z

A: Given system:

Q: The system is made up of the 1-m, 6.5-kg uniform rod AB and the two uniform disks (each of 0.15 m…

Q: 10" 6" D - - 9 lb 10° Y

A: Given,

Q: The double pulley shown has a mass of 15 kg and a centroidal radius of gyration of 160 mm. Cylinder…

Q: A horizontal force of P= 100 N is applied to the 250-kg reel of cable. The reel rests on rollers at…

A: To calculate the initial angular momentum I have just taken the moment about point o and then solved…

Q: Example 7 The 100-lb wheel has a radius of gyration of kg = 0.75 ft. If the upper wire is subjected…

A: The weight of the wheel is W=100 lb. The radius of gyration of the wheel is kG=0.75 ft. The tension…

Q: If the system starts from rest and no slipping occurs and cylinder A weighs 450 N and has a radius…

A: Given: Initially system is at rest and There is no slipping between cylinder and surface. Thus…

Q: The assembly consists of two 25-kg bars which are pin connected. The bars are released from rest…

Q: The 17-kg punching bag has a radius of gyration about its center of mass G of kg = 0.36 m. (Figure…

Q: The 19-kg punching bag has a radius of gyration about its center of mass G of kg = 0.45 m. (Figure…

Q: A slender 6-kg rod can rotate in a plane about a pivot at B. A spring of k = 600 N/m (unstretched…

Q: 4. A uniform disc of mass m = 3 kg and radius R=0.5 may roll without slip on the 30 degree incline…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

B
2. The pendulum consists of a 5-kg thin
cylinder fixed to a 0.6 m long rod with a
mass of 2-kg. e 0.80. The pendulum is
released from rest when e
Determine the maximum angle of rebound
- 90°.
after the cylinder strikes the floor.
0.09 m
0.6m
0.09 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given details

VIEW

Step 2: Before collision

VIEW

Step 3: After collision

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 269-lb block is released from rest when the spring is unstretched. The drum has a weight of 90 lb and a radius of gyration of ko - 0.9 ft about its center of mass O. The coefficient of stiffness of the spring is k-84 Ib/ft. The radius of the drum are: F-0.424ft and fou"0.89t. The velocity of the block after it has descended d-7 feet. Give your answer with 1 decimal.
The pendulum of the Charpy impact machine has a mass of 57 kg and a radius of gyration of ka = 1.52 m. If it is released from rest when e = 0°, determine its angular velocity just before it strikes the specimen S, e = 90°. 1.25 m Go Add your answer
Can anyone help me with this question
Please and thank
Dynmaic i need help solving the second part
The spool has a mass of 31 kg and a radius of gyration of ko = 0.3 m. The 10-kg block is released from rest. Neglect the mass of the cord. 300 mm00pm Part A Determine the distance the block must fall in order for the spool to have an angular velocity w = 15 rad/s. Express your answer to three significant figures and include the appropriate units. ANSWER: Part B What is the magnitude of the tension in the cord while the block is in motion? Express your answer to three significant figures and include the appropriate units. ANSWER: T =
The 25-kg uniform thin hollow square plate is pinned at point O, and its side L = 0.6 m. If it is subjected to the constant moment M = 83 N•m and is released from rest from the position as shown, determine the total work done to it when it has rotated O 45. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper SI unit. Take g 9.81 m/s². M 1/2 Your Answer: Answer units
The spool has a mass of 30 kg and a radius of gyration of ko = 0.3 m. The 10-kg block is released from rest. Neglect the mass of the cord. (Figure 1) Figure 300 mm 500 mm 1 of 1 Part A Determine the distance the block must fall in order for the spool to have an angular velocity w = 15 rad/s. Express your answer to three significant figures and include the appropriate units. S = Submit Part B T = ■ Value Submit O μA ☐ Request Answer What is the magnitude of the tension in the cord while the block is in motion? Express your answer to three significant figures and include the appropriate units. μÅ Value Units Request Answer ? Units ?
The vertical 2-kg bar AB is attached to the 3-kg cart by a pin at A andthe cord BC. Determine the tension in the cord immediately after the assembly is released from rest in the position shown.
The uniform 45 kg slender rod is at rest in the position shown when P = 525 N is applied. What is the total work done U1-2 when the rod goes to vertical position? Take L1 = 3.75 m and L2 = | 4.75 m. L2 L1 B
The 150-kg wheel shown in Fig. In the initial position shown, the velocity of Gis 2 m/s down the plane, and the spring is stretched 150 mm. If the spring modulus is 1000 N/m, what will be the maximum stretch of the spring? has a radius of gyration of 360 mm with respect to its center of mass G. www 150 kg 30°
3. A yo-yo has a weight of 0.3 lb and a radius of gyration ko = 0.06 ft. If it is released from rest, determine how far it must descend in order to attain an angular velocity @ = 70 rad/s. neglect the mass of the string and assume that the string is wound around the central peg such that the mean radius at which it unravels is r = 0.02 ft.