The double pulley shown has a mass of 15 kg and a centroidal radius of gyration of 160 mm. Cylinder A and block B are attached to cords that are wrapped on the pulleys as shown. The coefficient of kinetic friction between block B and the surface is μs = 0.2. Given that the system is at rest when the 200 N force is applied to cylinder A, determine the velocity of cylinder A as it strikes the ground.

Q: A cable connects the center of cylinder A (diameter = 0.8m) to the hub of cylinder B as shown below.…

A:

Q: In Figure 6(b), the rotating elements B, which weigh 1288 lb and have a radius gyration of k =…

A: Given: The weight of B, M = 1288 lb The weight of A, m = 2.78 lb The radius of gyration, k = 2.5 ft…

Q: The vertical position of the 165-kg block is adjusted by the screw-activated wedge. Calculate the…

A:

Q: 6. Two blocks A and Bare connected to the weightless links as shown in the image below. 1) If the…

A:

Q: d; and the 1.5 kg piston P are connected through the mechanism shown. 90mm AB crank rotates at…

A: Givenlength BD, l=200mmmass of BD, m1=1.2kgmass of pistion m2=1.5kglength of crank AB…

Q: The 46-kg cylinder has an angular velocity of w = 34 rad/s when it is brought into contact with the…

A: The time required to stop spinning the cylinder and the force in the link AB. Given: The mass of the…

Q: The force Pis applied to the 36-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: The arms of a Proell governor are 275 mm long and are pivoted on the axis of rotation. The…

A: The answer is in next slide

Q: The uniform rod has a weight W and rests on a smooth peg at C and against a wall at A. The…

A:

Q: The masses of blocks A and B of Fig. 50 kg and mg = 75 kg. If the coefficient of friction is 0.25…

A:

Q: 3. A block of mass m= 2.00 kg rests on the left edge of a block of mass M= 8.00 kg. The coefficient…

A: Part a) A free body diagram is a geometric representation of all the forces acting on the system. It…

Q: A cable connects the center of cylinder A (diameter = 0.8m) to the hub of cylinder B as shown below.…

A: FBD of AmA=38kgrA=0.4m

Q: Identify the type of ensuing motion of the discs and draw the free body, kinematic and kinetic…

A: Type of ensuing motion:The ensuing motion of the discs will be a combined rotation about point A and…

Q: A car of mass 700 kg travels round a horizontal curve of 60 m radius. The centre of gravity of the…

A:

Q: The 25-lb slender rod has a length of 6 ft. Using a collar of negligble mass, its end A is confined…

A:

Q: The 10 kg slender bar AB, shown in the figure, has a length of 2 m. A block of negligible mass,…

A: Given:- Weight of slender bad AB=10 kg Length of bar AB= 2m Coefficient of kinetic friction, µk =…

Q: Read and Solve carefully please Write clearly and Box the Final answer(s) Express your answer to 3…

A:

Q: 12 The 40-kg disk A with a radius of 0.5 m and the 30-kg crate B is attached to each other using the…

A: Given data: -  The mass of the disk is mA = 40 kg. The radius of the disk is r = 0.5 m. The mass of…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: The 25-lb slender rod has a length of 6 ft. Using a collar of negligible mass, its end A is confined…

A: Given Datam=25 lbL=6ftr=32 ftμB=0.28θ=30°

Q: What torque must be applied to the cylinder to keep it rotating?

A: Given: To determine: Torque applied

Q: The force P is applied to the 37-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: 2) The 25-lb slender rod has a length of 6 ft. Using a collar of negligible mass, its end A is…

A: The weight of rod, W = mg = 25 lb The length, L = 6 ft The position, r = 3x20.5 The angle = 30…

Q: The two uniform thin discs shown in the figure rest on a horizontal plane and are connected through…

A: In this question, it is asking about the solution of part B only so we will provide the solution for…

Q: The 12-lb disk A has a radius rA = 6 inches and an initial angular velocity ω0 = 750 rpm in a…

A:

Q: Problem 2.2: The 20-lb disk rests on the 5-lb plate. A cord is wrapped around the periphery of the…

A:

Q: The coefficient of kinetic friction between the 43-kg crate and the slanting floor is μk = 0.33 and…

A:

Q: The force Pis applied to the 41-kg block when it is at rest. Determine the magnitude and direction…

A: Use concept of maximum Static force and applied or self weight concept to approach this problem

Q: For the system shown, the masses of A and B are 65 kg and 145 kg, respectively. The coefficient of…

A:

Q: The 136-kg spool has a radius of gyration about its mass center of ke = 300 mm If the couple moment…

A:

Q: 8. The 20 kg uniform disk of radius r= 0.4 m is at rest on the incline (0 = 20°) when a constant…

A:

Q: The system shown below consists of a uniform disk D that has a mass of mD=2.8 kg and a radius of r =…

A: Given that, Mass of the disk, mD=2.8 kg,Radius of disk, r=0.5 meters,Angular acceleration of disk,…

Q: A 16-lb spool is at rest on an inclined surface. Around its center a cable is wound which travels…

A:

Q: A bar of mass mb is to be released from rest at the position shown. Three possible designs use…

A: Given: To find: Which would move fastest and slowest

Q: rope

A: using expression T2/T1 = e^μθ we have calculated  μ = 0.2159   free body diagram

Q: The 300lb body A and the 400lb body are connected by a cable passing over a smooth pully on the…

A: Given Data Weight of block A is: WA=300 lb Weight of block B is : WB=400 lb Coefficient of friction…

Q: A 1.6-kg sphere S is being moved in a vertical plane by a robotic arm. When the angle e is 38, the…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.