2. The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The properties of the segments and the working stresses are listed in the table. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 in. and the working stresses are not to be exceeded. A (in.?) E (psi) Ow (psi) Steel 0.75 30 x 106 20000 Bronze 1.00 12 x 106 18 000 Aluminum 0.50 10 x 106 12000 Bronze Steel Aluminum 4 ft 2 ft 3 ft 2P ЗР 4P

2. The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The properties of the segments and the working stresses are listed in the table. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 in. and the working stresses are not to be exceeded. A (in.?) E (psi) Ow (psi) Steel 0.75 30 x 106 20000 Bronze 1.00 12 x 106 18 000 Aluminum 0.50 10 x 106 12000 Bronze Steel Aluminum 4 ft 2 ft 3 ft 2P ЗР 4P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: PLEASE ANSWER NO. 1. SHOW THE DETAILED SOLUTION. THANK YOU AND GOD BLESS. SUBJECT: DYNAMICS OF RIGID…

A: To find:- acceleration

Q: 1. The velocity of a particle moving along the x-axis is defined by v-x³-4x² + 6x where v is in ft/s…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: The frame ACD is hinged at A and D and is supported by a cable that passes through a ring at B and…

Q: Problem 8 Figure 1 of 1 18 in. 30 5 in. > Part A Which of the following is the correct expression to…

Q: Slider block A moves to the left with a constant velocity of 6 m/s. Determine the velocity of block…

Q: Assume cc=0.62 and cy-0.98, calculate the discharge through a 120-mm diameter orifice under a head…

A: D=120mm h=6.5m Cc=0.62 Cv=0.98

Q: The motion of the slider A is defined by the relation x = 200 sin kt, where x and t are expressed in…

Q: Subject: Statics of Rigid Bodies Complete answer and clear hand writing Dont forget the free body…

Q: Block A of 500-kg mass is subjected to a towing force F = 2000t² + 3000t (Newtons)F= 2000r² + 3000…

A: Soluiton: Given: F=2000t2+3000t N μ=0.2 W = 500 kg θ=45o t = 4 s Tj=12mVf2 Work done =Fs…

Q: Question: 1. Find the centroid of an object 2. Draw an FBD diagram.

Q: © 20,000 N (tension) 1500 N (compression) D1000 N (tension) 2000 N (compression) O 1500 N (tension)…

A: First we will calculate the time taken to stop the train. Then using conditions of equilibrium we…

Q: 2.) Determine the distance travelled by the 50-kg block and the time it will take as it comes to…

A: Inclination of plane, mass of block, kinematic coefficient and initial velocity is given and it has…

Q: A closed tank contains 2.0 m of SAE 30 oil (s = 0.89), 1.5 m of water (y = 9790 N/m^3), 25 cm of…

Q: A rectangular gate 1.5m wide and 3m high is vertically submerged in water with its top edge…

Q: A car is traveling around a circular track of 730-ft radius. If the magnitude of its total…

A: Radial acceleration: It is defined as, in radial or circular motion, the acceleration of the object…

Q: wind and waves 3. Jesus commanded His disciples to go to the other side of the sea without Him, and…

A: Consider a rigid body. When the force is applied on it, it does not move, i.e., it is in…

Q: At a spot in the ocean water where the total depth is 500 m, oceanographers measures data below the…

A: USing the pressure equation find guage pressurePG=ρ1gh1+ρ2g(h2-h1)+ρ3g(h3-h2-h1)Pabs=PG+Patm

Q: Problem 3: As shown, a solid cylinder with a diameter of 0.30m and weighs 180 N has a cord wound…

Q: A rectangular scow has a draft of 1.8 m in fresh water when erect. The scow is 6m wide and 12m long…

Q: A subway train made of two cars is shown. It travels at a speed of 50kph. When the brakes are…

Q: A composite bar consist of two materials aluminum and steel is rigidly attached to the fixed…

Q: The discharge through a Venturi meter is 58 li/sec. The diameter of the pipe is 750 mm and the area…

A: Calculate the diameter of the throat, Area ratio = dpipedthroat 41=750dthroat…

Q: Q5. Determine the resultant magnitude of the hydrostatic force that water exerts on the wall along…

Q: Write the applications of temperature and pressure in engineering design.

A: Temperature and pressure carry an important role in engineering applications and designs. It has…

Q: 4. Solve the force reaction at member BE. Use any method E D 2 kN 3 m 3 m 3 m C.

Q: Civil Engineering Department Answer Sheet Date: Time: P-400 30

Q: Subject: Fluid mechanics

A: Given data Discharge at A, QA= 10 ft3/sec QA+QB= 10 ft3/sec …(1) Hence head loss in B and…

Q: 3.49 Determine the minimum volume of concrete (y = 23.6 kN/m²) needed to keep the gate (1 m wide) in…

Q: A flow field has x and y components of velocity (w = 0) defined as follows: u = 2x v = x + 2y (u and…

A: The correct option is ax=4x and ay=4x + 4y

Q: SIT. A The block is projected up a 15° incline at A with an initial velocity of 10 m/s. If the…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: roblem 5.1.6 5.1.6 WP The pump shown in Fig. P5.1.6 produces a steady flow of 10 gal/s through the…

Q: A vertical rectangular gate 1.8m wide and 4.2m high is submerged in oil (SG-0.88) with its bottom…

Q: A composite bar consist of two materials aluminum and steel is rigidly attached to the fixed…

Question

Subject: Mechanics DB

Answer the image below. Also draw the FREE BODY DIAGRAM, thank you

2. The compound bar containing steel, bronze, and aluminum segments carries the axial loads
shown in the figure. The properties of the segments and the working stresses are listed in the
table. Determine the maximum allowable value of P if the change in length of the entire
bar is limited to 0.08 in. and the working stresses are not to be exceeded.
A (in.?)
E (psi)
O» (psi)
Steel
0.75
30 x 106
20000
Bronze
1.00
12 x 106
18 000
Ahuminum
0.50
10 x 106
12000
Bronze
Steel
Aluminum
4 ft
2 ft
3 ft
P
2P
3P
4P

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 1 Please choose the correct answer and also write down your solution. (1) The beam is subjected to the shown loading. What is the correct statement regarding the flexural stress at A and B? P P a. Both og and og are tensile stress. 0.5 m 0.5 m 0.5 m b. Both oa and og are compressive stress. Og is tensile stress and og is compressive stress. с. d. OA is compressive stress and og is tensile stress. A В (2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio of the magnitudes of the maximum tensile and compressive flexural stresses over the a-a cross section? b. 3/7 a. 7/2 d. 2/10 е. 3/10 h. 10/3 c. 7/3 f. 10/2 i. 1/1 g. 2/7 250 mm 20 mm 60 mm 200 mm 2 m 1 m 15 mm 15 mm
please draw fbd
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
ASAP Hi! Can you help me with this problem? I'm having trouble answering this, I will give thumbs up for your answer. Thank you!
The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 inch and the working stresses listed in the table are not to be exceeded. Steel 2 ft Bronze 4 ft Aluminum 3 ft 2P 3P 4P A (in.?) E (psi) a. (psi) Steel 0.75 30 x 10 20000 12 x 10 10 x 10 Bronze 1.00 18000 Aluminum 0.50 12000
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
Dont round off initial values, round off final ans only pls
PLEASe answer this question. Thank you
Topic: COMBINED STRESS - STEEL DESIGN Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee
PLS PROVIDE COMPLETE SOLUTION THANKS
A beam carrying an allowable actual moment of -38 KN- m is reinforced as shown. If the the concrete is normal weight and f'c = 25MPa and fy = 420MPa. Determine the following: a. The cracking moment of the beam. b. The transformed moment of Inertia. c. The actual tension steel stress. d. Check the stress if it is correct by force checks. mm www.009 4-020 О 140 mm 300 mm 170 mm * 170 mm: ww.08 ✓ 60 mm
S=25