2 2. The assembly shown in Fig, 2 consists of one circular disk and two rods. The disk is pin joinedto the rods. The rods are pin supported at 0 and C, respectively. If the disk is rotating withı aclockwise angular velocity w= 3 rad/s at the instant shown, determine the velocities of points A andB. Also, caleulate the angular vclocities and @n of rods AO and BC, respectively. Specifyclockwise (CW) or counterciockwise (CCW) for the angular velocities a and we.to- 3 rad/s

Answered: Image /qna-images/answer/5cb80c68-5eb3-4acb-a011-714409a55505.jpg

2. The assembly shown in Fig. 2 consists of one circular disk and two rods. The disk is pin joined to the rods. The rods are pin supported at 0 and C, respectively. If the disk is rotating with a clockwise angular velority w= 3 rad/s at the instant shown, determine the velocities of points A and B. Also, calculate the angular velocities and @n of rods AO and BC, respectively. Specify clockwise (CW) or counterclockwise (CCW) for the angular velocities w a and @r. to-3 rad/s

2. The assembly shown in Fig. 2 consists of one circular disk and two rods. The disk is pin joined to the rods. The rods are pin supported at 0 and C, respectively. If the disk is rotating with a clockwise angular velority w= 3 rad/s at the instant shown, determine the velocities of points A and B. Also, calculate the angular velocities and @n of rods AO and BC, respectively. Specify clockwise (CW) or counterclockwise (CCW) for the angular velocities w a and @r. to-3 rad/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ذني السؤالين اريد جوابهن ممكن
slove f
1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Ql. The bracket is made from steel with Eseel = 120 GPa and poison ratio, v = 0.28. The following readings are obtained for each gauge under loadings: Ea=[X+Y] (10*) Es = -200(10-6) E= -180(106) Important note : X=100 Y=60 (a) Prove that &=Ea and &= E,. (b) Determine the shear strain, y and the normal strain, &, and E,. (c) Estimate the in-plane principal strains and the angle associated with the principal strains, and
(b) A differential element on the bracket as shown in Figure 1 is subjected to plane strain that has the following components: ex = 150µ, ey = 200µ, yxy = -700µ. By using the strain transformation equations, determine: - (i) The equivalent in-plane strains on an element oriented at an angle 0 = 60° counterclockwise from the original position. (ii) Sketch the deformed element within the x' – y' plane due to these strains. (iii) The stresses on the oriented planes in (I) where the value of elasticity, E = 200 GPa and Poisson's ratio, v = 0.32. (iv) Give your comments on those stresses in (iii) in terms of elastic limit/failure if the material's yield strength in tension/compression is 250 MPa and in shear is 90 MPa.
Ģ₁ G6 ਸਿੰਘ G G₁ Họ G G @TOO,
Draw the front, Side and top
(b) In Figure Q5, the 17 kg of circular disk is originally rotating with a clockwise angular velocity, o = 49 rad/s at the end of the link BC. Given the kinetic coefficient of friction, uk = 0.25 when the disk is then placed against the wall. (i) Draw the kinetic diagram of all forces exerted on the circular disk. (ii) Calculate the force of link BC. (iii) Calculate the angular acceleration of the circular disk. (iv) Calculate the time required to stop the motion of the circular disk,
Determine the following: x, y, Ix, Iy 1. y -240 mm 16 mm 12 mm 150 mm -10 mm 12 mm 16 mm 180 mm-
The 10-kg crate is subjected to a force having a constant direction and a magnitude F = 100 N. When s = 15 m, the crate is moving to the right with a speed of 8 m/s. Determine 1) The normal force between the crate and the ground. 2) Its speed when s = 25 m. %3D The coefficient of kinetic friction between the crate and the ground is mk = 0.25.