2. Make ten measurement for the diameter of the spherical ball first with vernier caliper, then micrometer.Then, fill the table with your results.VernierMicrometerNo.Caliper (mm)6.056.05(mm)5.966.04236.006.0245.905.986.105.9465.856.085.955.956.005.996.005.98106.056.00Determine average absolute deviation, sample standard deviation, sample variance and coefficientof variation for diameter measurement at Instruction 2 for both vernier caliper and micrometer.

Mean calculated is 5.9+6.12=6Now calculate deviation from mean S.no Deviation from…

2. Make ten measurement for the diameter of the spherical ball first with vernier caliper, then micrometer. Then, f the table with your results. Micrometer (mm) 5.96 6.04 Vernier No. Caliper (mm) 6.05 6.05 6.00 5.90 6.10 5.85 3 6.02 4 5.98 5 5.94 6.08 5.95 5.99 6.00 5.98 5.95 6.00 6.05 10 6.00 . Determine average absolute deviation, sample standard deviation, sample variance and coefficient of variation for diameter measurement at Instruction 2 for both vernier caliper and micrometer.

2. Make ten measurement for the diameter of the spherical ball first with vernier caliper, then micrometer. Then, f the table with your results. Micrometer (mm) 5.96 6.04 Vernier No. Caliper (mm) 6.05 6.05 6.00 5.90 6.10 5.85 3 6.02 4 5.98 5 5.94 6.08 5.95 5.99 6.00 5.98 5.95 6.00 6.05 10 6.00 . Determine average absolute deviation, sample standard deviation, sample variance and coefficient of variation for diameter measurement at Instruction 2 for both vernier caliper and micrometer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

make a three-view drawing, complete with dimensions, of the part. Show the dimensions with the view that best shows the shape of the part or feature. Use : creo parametric 3.0
Can you send me the top, front and right view of the given diagram with correct dimensions
I need the answer as soon as possible
answer the first question then the second, as per bartley policy my 2 questions are FINE to be submitted.
Show the tolerance zone created by each of the given tolerance specfication. Superimpose the tolerance zone on the given drawing.
15.00 +0.25 Engineering drawings with tolerances are shown below for three blocks: A All units in cm ↑ 11.0+ 0.4 All units in cm Calculate the nominal, minimum, and maximum height (in cm) of the three-cube stack shown at right. The cubes are stacked atop each other with no gaps between them. Pay special attention to units, and note that 1 inch equals exactly 2.54 cm. 1. Nominal height = 2. Minimum height= 3. Maximum height = A Hints: • For each cube, calculate the nominal, minimum, and maximum height using the nominal heights and tolerances provided in the three drawings. . Ensure that the cubes' heights and tolerances are all in the same units before adding them in the next step. • Add the three nominal heights to find the nominal height of the stacked cubes. Do the same for the three minimum heights and three maximum heights. The tolerance table for cube C does not apply to the drawings for cubes A • or B. B cm C 3.10 All units in inches cm 3.1 cm ??? As a reminder, do not round your…
Please see attached.
6. Comment on accuracy and precision of the spherical ball diameter measurements at Instruction 2 2. Measure the diameter of spherical ball five times with micrometer Then, fil the table with your results. No. Micrometer (mm) 1st 8.01 2nd 8.00 3rd 8.00 7 99 7 08 4th 5th
Calculate the Maximum X distance on the drawing below: 1.000 .510 O 3.000 2.009 O 1.996 2.000 с 2.000 Ø.995-1.000 6.00 0.008 MABC X 3.000 Y 01.005-1.030 +0.005MABC B A XX = .01 ANGLES= ± 1°
I need the answer as soon as possible
If the difference in the taped distance and paced distance is 0.90 m and the tape distance is 362.70. What is the relative precision of the measurement?
Given the drawing below, answer questions