4X.50X 2.38 2X Ør.00 4.50 4x Ø.50- 3.00 62 62 1.56 219 3.31 238 3.94

Q: Name: Q1/ Give the Name of plans in the Image? The anatomical planes www.free-anatomy-quiz.com Q2/…

A: Plane A -Frontal PlanePlane B -MidSagittal Plane Plane C - Transverse Plane

Q: the sketch top, front, and right side isometric below. For the objects shown in sure that your views…

A: According to the details provided in the question we need to draw three projection view of the given…

Q: can you do it in polygon

A: Given vectors : A :  2 kph 45°N of E B :  2.8  kph 58°E of S C :  5.1  kph 28°W of S D : 3.2  kph…

Q: What are the two dimensions that are not placed on the field of a drawing? A zero and a 45 degree…

A: The following things needs to be mentioned on the field of drawing: ◆ The diameter or radius of…

Q: The object shows the center of the whole is three inches from the left surface and one inch from the…

A: we have to determine what kind of dimensions are used in the hole

Q: Draw the orthographic views of the following isometric figure.

A:

Q: Draw, using 1 st angle projection Orthographic view of the following figure  with  suitable scale,…

A: (a) the given front elevation;

Q: For the given isometric drawings, draw the corresponding top, front, and right side views

A: Note: As per policy, we can solve the first question from the multiple questions. Please resubmit…

Q: Draw the orthographic views of the following isometric figure. (units in mm

A:

Q: Q) Draw the following projections for the figure shown with scale 1:1. 1. Front View 2. Side View 3.…

A: Solution:

Q: Draw back the drawing given  with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: Using the drawing below identify th mistake on dimensioning rules and write the correct method to…

A: According to DG&T standards, there are 5-dimensional mistakes that are highlighted in the fig…

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: 2. For the plan area shown, determine the location of the Centriod. Use you're the last two digits…

A:

Q: Creste an sometre ptora and thena caet ut l the folloing abject. The grid soacing is 10 mm.

A:

Q: The top one (first drawing) is a top view. The second one or lower one is a side view. Please draw…

A: given : top and side view

Q: 1. Nominal surface the surface that represents the desired specifications on a part drawing nominal…

A: The measurement of small-scale differences in the height of a physical surface is known as…

Q: Based on the following orthographic projections for each object, generate a full-scale isometric…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: For the given multiview projection, draw the corresponding isometric drawing. ME DA

A: For the given multi view projection, draw the corresponding isometric drawing.

Q: Please answer questions 12

A: as per our guide lines 1solved 12th question only

Q: Circle the letter corresponding to the correctly aligned set of orthographic views. 1. 2. A 6:6 A E…

A: according to the drawing data we need to find, the right option. that represent the three…

Q: 1ST Dimensions and projections

A: 1 st angle projection

Q: Draw the isometric projection of the object showing the top, front and right side.

A:

Q: QUESTION 2: DRAW IN DIMENSIONS THREE STANDARD PROJECTIONS OF THE ISOMETRICS SHOWN BELOW. ASSUME NO…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: SolidWorks to create the parts.

A: I am using Solidworks to draw a 3-d object of the given problem.

Q: Choose dimensions for the object shown. Place extensions, dimenstions, leader lines and arrows. Omit…

A: Choose dimensions for the object shown. Place extensions, dimenstions, leader lines and arrows.

Q: Ф 20 30 75

A: Representation of three-dimensional shapes into two-dimensional is known as isometric projection. In…

Q: Name: Create an isometric pictorial and then a cabinet oblique pictorial of the following object.…

A:

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: Given the Isometric views, draw the three orthographic views below

A: Orthographic views of the given isometric view are drawn on the grid paper. 1 Grid = 1 unit.

Q: DRAW THE ISOMETRIC FIGURES OF THE ORT

A: According to the details provided in the question, we need to draw an isometric view

Q: 100 82 20 32 96 Top view Isometrie view

A: Top view Top view of object is obtained when we see object from top.   Front view Front view of…

Q: Based on the following orthographic projections for each object, generate a full-scale isometric…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Use blank or isometric grid paper to draw the isometric views of the following objects.

A: Draw the given three views.

Q: Draw the orthographic views of the following isometric figure. (units in mm

A:

Q: Need you to draw orthographic views of this object.

A: The required orthographic views are drawn using third angle method of projection.

Q: Make an Isometric Drawing of the support bracket shown in Figure 4. Take the dimension 'H' as 35 mm.…

A:

Q: Draw the isometric views of the following shapes in 1st angle projection

A: Solution: Isometric view means making 3 dimensional figure . The isometric view of given figure is…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.