100 82 20 32 96 Top view Isometrie view

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: draw isometric diagram with measurement labels

A:

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: Given the isometric drawing, draw the multiview projection. The multiview projection of the glass…

A: Draw the isometric view.

Q: One end of a piano wire is wrapped around a cylindrical tuning peg and the other end is fixed in…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: I need answers for problems 1, 2, and 3 pertaining to the print provided.

A: (1). Yes, the detail drawing is of a single part namely the Bonnet Sleeve.

Q: I need these three parts answered, if you can not answer all three parts please leave it for another…

A: 8.Refer to the drawing. The material specified for the given part is brass. It is shown in the…

Q: I need problems 4, 5, and 6 answered.

A: (4) In engineering drawing SR is denoted for radius of sphere. So the answer will be,.562” spherical…

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: I need answers to questions 4, 5, and 6 pertaining to the print provided.

A: Since we question only one question, we will answer the question no. 10. Please submit the question…

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: P4-2) Answer questions about the following drawing. a) How many linear dimensions? b) How many…

A: As we are entitled to solve upto three subpart. I am solving here the first three parts for You. To…

Q: For problems 1 and 2 below, using the Parallelogram method only (no other method will be accepted)…

A:

Q: 1.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: Sure, based on the information provided in the text accompanying the image, the angle between lines…

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: Using the rules of projection find the true length of line AB using a 1:5 METRIC scale.

A: Given condition

Q: I need these 3 parts answered. In manufacturing, dimensions often may fall in a range. For example,…

A: 1-In manufacturing, dimensions often may fall in a range. For example, for three-place decimals, the…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.