2. In the hanger shown, the upper portion of link ABC is 3/8 in. thick, and the lower portions are each 1/4 in. thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A is of 3/4 in. diameter while a 3/8 in. diameter pin is used at C. Determine: 1.25 in. the shearing stress in pin A the shearing stress in pin C the largest normal stress in link ABC the average shearing stress on the bonded surfaces at B the bearing stress in the link at C 6 in. 1.75 in. 7 in. 10 in. 300 lb 5 in.

2. In the hanger shown, the upper portion of link ABC is 3/8 in. thick, and the lower portions are each 1/4 in. thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A is of 3/4 in. diameter while a 3/8 in. diameter pin is used at C. Determine: 1.25 in. the shearing stress in pin A the shearing stress in pin C the largest normal stress in link ABC the average shearing stress on the bonded surfaces at B the bearing stress in the link at C 6 in. 1.75 in. 7 in. 10 in. 300 lb 5 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The aluminum rod AB (Gal = 27 GPa) is bonded to %3D the brass rod BD (Gpr = 39 GPa). The portion CD of %3D the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T. 60 mm 2T 36 mm T 250 mm 375 mm 400 mm
A composite beam is made of two brass [E = 97 GPa] plates bonded to an aluminum [E = 72 GPa] bar, as shown. The beam is subjected to a bending moment of 2420 N-m acting about the z axis. Assume b=64 mm, d1=36 mm, d2=13 mm. Determine: (a) the maximum bending stresses opy,Gal in the brass plates and the aluminum bar. (b) the stress in the brass obrj at the joints where the two materials are bonded together. Brass (2) d2 Aluminum (1) Brass (2) dz b Answers: (a) obr = i MPa, oal = i MPа. (b) Obrj MPa.
H.W 3 Two aluminum alloy plates (2) are attached to the sides of a wooden beam (1) as shown in Figure 3. mensions of the composite cross section are b1 = 80 mm, d¡ = 240 mm, b2 = 10 mm, d2 = b2 The di- |di 120 mm, and a = 60 mm. Deter- (2) (2) %3D mine the maximum bending (1) a stresses produced in both the wooden beam and the aluminum b1 plates if a bending moment FIGURE 3 +6,000 N m is applied M2 %3D about the z axis. Assume that Ej = 12.5 GPa and E2 = 70 GPa.
When designing a structural member, which of the following statements is FALSE? A. The allowable stress is used in calculating the maximum load to be applied. B. The ultimate stress depends on the Factor of Safety used. C. The ultimate stress is determined based on the material used. D. The allowable stress depends on how conservative the design is. Which of the following is NOT a valid reason for increasing the Factor of Safety? A. Higher uncertainty in loading conditions B. Higher design life C. Lower confidence in assumed/stated material properties D. Lower member importance Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa
The composite beam is made of steel (A) bonded to brass (B) and has the cross section shown. It is subjected to a moment of M = 6.3 kN?m .Ebr = 100 GPa, Est = 200 GPa A: Determine the maximum bending stress in the brass. B:Determine the maximum bending stress in the steel. C: Determine the stress in the brass at the seam where the brass and steel are bonded together. D:Determine the stress in the steel at the seam where the brass and steel are bonded together. B M 175 mm 150 mm 200 mm
pls help me. thank u refer to the picture attached below.
Question 4a pls
H.W 3 Two aluminum alloy plates (2) are attached to the sides of a wooden beam (1) as shown in Figure 3. mensions of the composite cross section are bj = 80 mm, d1 = dz 240 mm, b2 = 10 mm, d2 = The di- di %3D %3D 120 mm, and a = 60 mm. Deter- (2) (2) (1) mine the maximum bending stresses produced in both the wooden beam and the aluminum b1 plates if a bending moment M = +6,000 N m is applied about the z axis. Assume that E = 12.5 GPa and E2 = 70 GPa. FIGURE 3 %3D