"2. In the following circuit R₁ = 2000, RL = 100k, n₁/n2 = 1/100, and vin (t) = 40 cos(wt)V, where w = 1000 rad/s: (a) Find the impedance Z₁. That is, the secondary impedance reflected to the primary. (b) Find the resistance seen by the source. (c) If Ry, is changed to 40k, find the value of n₁/n2 for maximum power transfer to RT. (d) Calculate the voltage in the primary and the secondary, V₂, and V, (where V, = Vout). (e) Calculate the currents I, and I, (primary and secondary)." vs(t) www R₁ 01:02 Z₁l ideal R₁ Vout

"2. In the following circuit R₁ = 2000, RL = 100k, n₁/n2 = 1/100, and vin (t) = 40 cos(wt)V, where w = 1000 rad/s: (a) Find the impedance Z₁. That is, the secondary impedance reflected to the primary. (b) Find the resistance seen by the source. (c) If Ry, is changed to 40k, find the value of n₁/n2 for maximum power transfer to RT. (d) Calculate the voltage in the primary and the secondary, V₂, and V, (where V, = Vout). (e) Calculate the currents I, and I, (primary and secondary)." vs(t) www R₁ 01:02 Z₁l ideal R₁ Vout

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Determine the value of the capacitor to be connected in parallel with ZL (load) in order to correct the power factor of the load to 0.90802.
A. Find the total impedence Zt in polar form. B. Draw the impedence diagram. C. Find the current and voltages Vr,VL and VC in phasor form. D. Draw the phasor diagram of voltage E,VR,VL and VC and the current I. E. Verify kirchoff's voltage law arround the closed loop. F. Find the average power delivered to the circuit. G. Find the power factor of the circuit, and indicate whether it is leading or lagging. H. What happened if Xc=2ohm? Please explain.
Please show all calculations in detail. The answer should be shown in both polar and cartesian form.
Ererrises: IA platinum oil has a resifance of 3-14k r at go°C and 3.747JV at 100°C.- Fin'd the resistance at o'C ond the kmp -creff. of resifonce af 40°C 2. A pofential difference of r5oV is apphed to a field wnding at 15°C and the currend is SA. What will be the mean fempouafure of the winiding when currend has falen to 3.91A, apphedvrltage being constant Aasume s =p7.5. 3. A cril has a resi fance of 182 when its mean femperature is 20°C and 20v when ik mean femperature s 50°C. Frid is mean femperature rise when ik resotonce is 21JL and the sorrandinig femperature is i5°C. A cril of a relay takes a curre of 0.12 A when it is at the vem insbi o al 4. A jemperature of is'C ond canneckerdacms a oV supply If the minimum operating current of the relay is 0.1 A, colculate the femperature above ohich the relay will fail to operate when connected ti the same supply. Resi tncenfemp.coefficrenf of the cril makria] is o.0043 per °C at 0°C.
The following is given for a series R-L-C circuit: resistor (R) = 8 Ohms, an inductor (L) = 32 mH and a capacitor (C) = 800uF. The circuit is supplied by a voltage source of e = 120 sin (125t) Volts. What is the angular frequency of the ac source? What is the period of ac source? What is the circuit impedance? What is the power factor? What is the real power of the circuit? What is the rms value of the circuit current?
4) Given: R = 700-N, Xc = - j 500-N, e(t) = 150 sin(wt) V Find: a) Total impedance of the ckt. b) Total current in phasor and sinusoidal form c) Voltage drop across the resistor and capacitor in phasor and sinusoidal form d) Total Power and Power factor
please I want an answer
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (I, in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1. and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. If the value of R2 =1600 Ohm then the input voltage (in volts) is: 7.5 25 110 Frequency H2 O a. 4 O b. 16 sin(9888 t) O c. 8 O d. 8 cos(6.28 f t) O e. 8 sin (6.28 R t)
Previous solution was incorrect...
1)The value of the capacitance reactive power in VAR is? /2) The value of the capacitor in micro farad is?
Introduction to Ac circuits. show detailed illustration and step by step solution
A certain impedance is given by 1012° N. Does the current lead or lag the voltage, and by how many degrees? Fill in the blanks. The current the voltage by