2. Given the following circuit below: R₂ ww Ig w R₁ Isz RL Vo Va Vs = 12V Is₁ = 3mA Is2=1mA R₁ = 4k R2=2ks? (a) Find the equivalent resistance RTH (b) Find the open circuit voltage Voc (c) Find the short circuit current Isc

I have a half size breadboard,9V source, multimeter, 220 resistor, (forward biased) 1N914 diode, in series.  Im reading about 9.7mA. The simulation reads close to 36mA. Can you help me to figure out if I am doing something wrong. (I lfet the battery a little unhooked so the resistor would not overheat). This image shows how I set up my circuit I need to read current first than volage the simulation  has another multimeter we are to relace with a jumper wire to read voltage of the diode. We first must read circuit currrent.

can you solve this question handwritten solution step by step how did we obtain the v0 graph? my question is not a part of a graded assignment

A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1

If the resistors used for charging and discharging were the same, the charging anddischarging waveform would be ________.a. Symmetricalb. Nonsymmetrical

A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4

Question 2) How to calculate icorr, ecorr, rp and corrosion rate manually. Use mild steel/aluminium in 0.5 M HCI Sweep potential from -50 mV to + 50 mV of the open circuit (OC) or freely exposed potential. Use 0.5 mV steps each second (0.5 mV s-1) Plot data E - i Determine the polarization resistance (Rp) Determine the Ecorr and the corrosion rate.

ExampleConsider the following electrical system as shown in the following figure. This circuit consistsof resistor, inductor and capacitor. All these electrical elements are connected in series. Theinput voltage applied to this circuit is vi and the voltage across the capacitor is the outputvoltage vo. Find vo/vi ?

2:50 1 LTE O Motor Warning Light Instructions PHYS&110-VHY-S21-PHYSNON-SCIMAJORSWLAB-.. STEP 3 Now add a red LED (D1 in the main schematic) in series with 500N of resistance (shown as R1 in the main schematic). How you choose to arrive at 5002 is up to you. SW1 PSB D2 D3 1N4007 5 V D1 Blue Red R3 10 ka R1 500 Q • What happens now when SW1 is (and the PSB is turned on)? • What happens if you turn the diode at D3 around? (Don't forget to turn it back the right way afterward.) • Why does this circuit use a diode at D3 instead of a pull-up resistor? (Meaning, what would happen if a resistor were used instead of the diode?) pressed ( Previous Next 14 Dashboard Calendar To Do Notifications Inbox