-2. Determine the state space for thesystem considering that a force F isapplied in m2.m =2kg1m2= 3kgb₁ = 0.5kgk1= 15k = 10NmNmS m₁ = 2 kgm2-3 kgb₁ = 0.5 kg/sk₁ = 15 N/mk₁ = 10 N/m

Sure, We are asked to determine the state space for the system considering a force F applied to mass…

Answered: - 2. Determine the state space for the…

Understanding Business

12th Edition

ISBN:9781259929434

Author:William Nickels

Publisher:William Nickels

Chapter1: Taking Risks And Making Profits Within The Dynamic Business Environment

Section: Chapter Questions

Problem 1CE

See similar textbooks

Similar questions

Discuss what we mean by multipole moments.
What Happens When a Process Exhibits PossibleNonrandom Variation?
Only typed explanation otherwise leave it
The mean service time (x¯) of a hairdresser is 18 minutes with a standard deviation (σ) of 2 minutes. Upper specification limit (USL) is 22 minutes, whereas lower specification limit (LSL) is 15 minutes for this process. What is the process capability index (cpk) for this process? Is the process capable? Cpk=0.67, capable Cpk=1.5, capable Cpk=0.67, not capable Cpk=0.5, capable Cpk=0.5, not capable
1m radius disk is moving on the inclined surface under no slip condition. the center of the disk has 3m/s velocity and according to the figure, bar BC is pinned to the disk at point C and point B always stays on the ground. 1) find angular velocity of BC. 2) find angular acceleration of BC
STAR Co. provides paper to smaller companies with volumes that are not large enough to warrant dealing directly with the paper mill. STAR receives 100-feet-wide paper rolls from the mill and cuts the rolls into smaller rolls of widths 12, 15, and 30 feet. The demands for these widths vary from week to week. The following cutting patterns have been established. 12-ft 15-ft 30-ft Trim Loss (ft) Min s.t. 12-f Pattern Number 15-1 1 30-1 2 3 4 5 0 D 8 3 7 6 0 0 0 1 0 3 0 2 0 10 Trim loss is the leftover paper from a pattern (e.g., for pattern 4, 3(12)+ 0(15) + 2(30) 96 feet used results in 100-96-4 foot of trim loss). Orders in hand for the coming week are 5,660 12- foot rolls, 1,690 15-foot rolls, and 3,340 30-foot rolls. Any of the three types of rolls produced in excess of the orders in hand will be sold on the open market at the selling price. No inventory is held. 10 (a) Formulate an integer programming model that will determine how many 100-foot rolls to cut into each of the five…
Hydronos is a Greek manufacturer of yogurts that have gained popularity in the United States, so it has recently built a U.S. production plant and distribution center. To ensure that it complies with U.S. environmental standards, Hydronos is planning to implement efforts to reduce emissions and other industrial waste at its manufacturing plants using a program called Green-100. Green-100 covers all company procedures, from reducing manufacturing emissions, to how the lights are controlled in the plant, to how the truck drivers complete their routes. For example, under the new Green-100 guidelines, Hydronos has measured the amount of fuel drivers need to complete their routes for traveling at moderate speeds. If drivers choose to drive at higher speeds, they will need to pay for any extra fuel they use. Hydronos also has plans to install speed governors in its fleet of trucks to ensure that the drivers do not exceed speeds of 80 miles per hour. Mangements' claim that the new technology…
17- According to a business plan for a startup, the break-even point was calculated at 12,000 units of sales. However, after launch, the average variable cost for the product has gone up. Which of the following is the effect on break-even point? Group of answer choices the effect on break-even point cannot be determined without more information the break-even point will remain the same the break-even point will be higher than 12,000 units the break-even point will be lower than 12,000 units 18- According to a business plan for a startup, the break-even point was calculated at 12,000 units of sales. However, after launch, the unit price for the product had to be lowered. Which of the following is the effect on break-even point? Group of answer choices the break-even point will remain the same the break-even point will be lower than 12,000 units the effect on break-even point cannot be determined without more information the break-even point will be higher than 12,000…
111) What is the range for the adjustment factor in the calculation of QALY? a) 0 - 1 b) 0 - 10 c) 0 - 100 d) 0 – 50
Which of the following takes place when a company sets its standards by comparing data from other companies and similar industries to its own? Choose one answer. Balancing Benchmarking Standard deviation Performance appraisal
In a manufacturing process, 10% of the produced units are defective. If the process produces 1000 units per hour, how many defective units are produced in a day (8 hours of operation)?
solve this

SEE MORE QUESTIONS

Recommended textbooks for you

Understanding Business

Management

ISBN:

9781259929434

Author:

William Nickels

Publisher:

McGraw-Hill Education

Management (14th Edition)

Management

ISBN:

9780134527604

Author:

Stephen P. Robbins, Mary A. Coulter

Publisher:

PEARSON

Spreadsheet Modeling & Decision Analysis: A Pract…

Management

ISBN:

9781305947412

Author:

Cliff Ragsdale

Publisher:

Cengage Learning

Understanding Business

Management

ISBN:

9781259929434

Author:

William Nickels

Publisher:

McGraw-Hill Education

Management (14th Edition)

Management

ISBN:

9780134527604

Author:

Stephen P. Robbins, Mary A. Coulter

Publisher:

PEARSON

Spreadsheet Modeling & Decision Analysis: A Pract…

Management

ISBN:

9781305947412

Author:

Cliff Ragsdale

Publisher:

Cengage Learning

Management Information Systems: Managing The Digi…

Management

ISBN:

9780135191798

Author:

Kenneth C. Laudon, Jane P. Laudon

Publisher:

PEARSON

Business Essentials (12th Edition) (What's New in…

Management

ISBN:

9780134728391

Author:

Ronald J. Ebert, Ricky W. Griffin

Publisher:

PEARSON

Fundamentals of Management (10th Edition)

Management

ISBN:

9780134237473

Author:

Stephen P. Robbins, Mary A. Coulter, David A. De Cenzo

Publisher:

PEARSON

SEE MORE TEXTBOOKS

- 2. Determine the state space for the system considering that a force F is applied in m2. m = 2kg 1 m2 = 3kg b₁ = 0.5kg k 1 = 15 k = 10 N m N m S m₁ = 2 kg m2-3 kg b₁ = 0.5 kg/s k₁ = 15 N/m k₁ = 10 N/m