Suppose you are analyzing processing times for a machining operation. In your analysis, you found C, = 2.1 andCpk = 1.28. Given this information, which of the following sigma levels is the highest that you could claim yourprocess is capable of meeting?O 1 sigmaO 2 sigma3 sigmaO 4 sigma5 sigmaO 6 sigma

Explanation: With the given values of Cp and Cpk, the 4 sigma level, can be achieved for the…

Answered: Suppose you are analyzing processing…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

Discuss the basic differences between the mean absolute deviation and mean absolute percent error.
The following data set was collected from a survey 60, 56, 46, 55, 42, 43, 57, 46, 49, 56, 55, 59. 49, 41, 52, 53, 46, 51, 54, 43, 41 If a frequency distribution is to be constructed with classes 40-44, 45-49, 50-54, 55-59, and 60-64, what is the frequency of the 40-44 class?
Would a data series that contains values grouped into 10 categories be better displayed as a pie chart or a column chart?
Bottles for room spray are supposed to weigh exactly 16 oz. Inspectors want to develop process control charts. They take five (05) boxes of four (04) bottles each and weigh them. They obtain the following data. The mean weights of each of the 05 samples are 15.2, 14.6,16.5,18.1, and 13.2 respectively. Likewise, the range values for the each of 05 samples are 0.4, 0.2, 0.4, 0.5, and 0.9 respectively. For the X-bar charts and R-charts, the Parameters, A2, D3 and D4 are respectively. Select one: a. 0.48, 0.00, 2.00 b. 0.25, 0.31, 1.69 c. 0.73, 0.00, 2.28 d. 0.37, 0.14, 1.86
9. Two machines are currently in use in a process at the Dennis Kira Mfg. Co. The standards for this process are LSL = .470" and USL = .476". Machine One is currently producing with mean = .474" and standard deviation .0003". Machine Two is currently producing with mean .4745" and standard deviation .0002". Which machine has the higher capability index? Machine One has an index of (round your response to two decimal places). (round your response to two decimal places). Machine Two has an index of Machine (1) (1) Two One has the higher capability index.
Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 5 pistons produced each day, the mean and the range of this diameter have been as follows: Day Mean (mm) Range R (mm) 158 4.3 151.2 4.4 155.7 4.2 153.5 4.8 156.6 4.5 What is the UCL using 3-sigma?(round your response to two decimal places). 1. 2. 4.
A process that produces computer chips has a mean of .04 defective chips and a standard deviation of .003 chips. The allowable variation is from .031 to .049 defective. a.Compute the capability index (C,) for the process. (Round your intermediate calculations to 3 decimal places and final answer to 2 decimal places.) Capability index
Other things remaining the same, and assuming that X is smaller than USL and larger than LSL, if the standard deviation (σ) of the process increases, process capability index (Cpk) of the process will: Stay the same Will always increase Will always decrease Will sometimes increase
COQ Histogram; Spreadsheet Application Genova Company classifies its costs of quality intofour categories. The costs of quality (COQ) as a percentage of cost of goods sold for the last threeyears are as follows:[LO 17-1, 17-5][LO 17-5]2019 2020 2021Prevention costs 1.00% 4.00% 2.00%Appraisal costs 3.00 2.50 1.50Internal failure costs 27.00 23.00 14.00External failure costs 31.00 18.00 12.00Required1. Use a spreadsheet to prepare a histogram that shows the costs of quality (COQ) trends as a percentageof cost of goods sold.2. Comment on the trends in cost of quality (COQ) over the 3-year period from 2019 to 2021.3. Based on the observed trends, what total cost of quality can the company expect in 2022? Explain.
The relative size of errors is shown by: Residuals MSE O Bias MAD MAPE
Which of the following graphical presentations is not appropriate for numerical data? histogram pie chart time-series plot scatter plot
A manufacturing company produces steel rods. The length of these rods is critical to their customers. The company aims to manufacture rods with a mean length of 150 cm. However, due to variability in the manufacturing process, the lengths of the rods follow a normal distribution. The company's quality control department samples 30 rods and finds that they have a mean length of 151 cm and a standard deviation of 2 cm. Calculate the Process Capability Index (Cp) and the Process Performance Index (Ppk) for this process. Assume the customer's specification limits are 147 cm and 153 cm for the length of the rods.

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS

Suppose you are analyzing processing times for a machining operation. In your analysis, you found Cp = 2.1 and Cpk = 1.28. Given this information, which of the following sigma levels is the highest that you could claim your process is capable of meeting?