A process that produces computer chips has a mean of .04 defective chips and a standard deviation of .003 chips. The allowable variation is from .031 to .049 defective. a.Compute the capability index (C,) for the process. (Round your intermediate calculations to 3 decimal places and final answer to 2 decimal places.) Capability index

A process that produces computer chips has a mean of .04 defective chips and a standard deviation of .003 chips. The allowable variation is from .031 to .049 defective. a.Compute the capability index (C,) for the process. (Round your intermediate calculations to 3 decimal places and final answer to 2 decimal places.) Capability index

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

A shirt manufacturer buys clothes by the 100-yard roll from a supplier. For setting a control chart to manage the irregularities (e.g., loose threads and tears), the following data were collected from a sample provided by the supplier. Sample 1 2 3 4 5 6 7 8 9 10 Irregularities 3 5 2 6 5 4 6 3 4 5 Which type of control chart should be used? Construct a control chart with two-sigma control limits. Suppose the next five rolls from the supplier had three, two, five, three, and seven irregularities. Is the supplier process under control? Explain and show work
Linda Boardman, Inc., an equipment manufacturer in Boston, has submitted a sample cutoff valve to improve your manufacturing process. Your process engineering department has conducted experiments and found that the valve has a mean of 8.00 and a standard deviation of .04. Your desired performance is = 8.0 ± 30, where o = 0.047. Is the following statement true or false? Can Boardman produce the valve within the specified tolerance? (TRUE=yes, it can; FALSE=no, it cannot) O True O False
Consider a process with lower process control limit as 1.338 and upper process control limit as 1.342 . The lower specification limit is 1.335 and the upper specification limit is 1.345. Utilizing the information provided, is the process is capable of meeting design specifications?
Refer to Table 56.1-Factors for Computing Control Chart Limits.(3.sigma) for this problem. Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced each day, the mean and the range of this diameter have been as follows: a) What is the value of x? mm (round your response to two decimal places). b) What is the value of R? R=mm (round your response to two decimal places). c) What are the UCL, and LCL; using 3-sigma? Day 1 2 3 4 5 Upper Control Limit (UCL;)mm (round your response to two decimal places) Lower Control Limit (LCL;)mm (round your response to two decimal places). d) What are the UCL and LCL using 3-sigma? Upper Control Limit (UCLR)-mm (round your response to two decimal places). Lower Control Limit (LCL)-mm (round your response to two decimal places) Mean x (mm) 154.9 151.2 155.6 155.5 154.6 Range R (mm) 4.4 4.8 4.3 5.0 4.7 Next
S Book Hint Print eferences Problem 13-2 (Algo) A metal fabricator produces connecting rods with an outer diameter that has a 1 ± 0.02 inch specification. A machine operator takes several sample measurements over time and determines the sample mean outer diameter to be 1.004 inches with a standard deviation of 0.006 inch. Calculate the process capability index for this example. (Round your answer to 3 decimal places.) Process capability index
A weighing process has an upper specification of 1.751 grams and a lower specification of 1.632 grams. A sample of parts had a mean of 1.7 grams with a standard deviaiton of 0.023 grams. Round your answer to four decimal places. What is the process capability index for this system?
Meena Chavan Corp.'s computer chip productionprocess yields DRAM chips with an average life of 1,800 hoursand cr = I 00 hours. The tolerance upper and lower specificationlimits are 2,400 hours and 1,600 hours, respectively. Is this processcapable of producing DRAM chips to specification?
Suppose that a quality characteristic is normally distributed with specifications at 100 ± 20. The process standard deviation is 6.(a) Suppose that the process mean is 100. What are the natural tolerance limits? Calculate Cp and Cpk and interpret these ratios. What fraction of parts do you expect to be defective?(b) Suppose that the process mean is 106. What are the natural tolerance limits? What is thefraction defective? Calculate Cp and Cpk and interpret these ratios.
7. An ad agency tracks the complaints, by week received, about the billboards in its city: Week No. of Complaints 1 3 2 6 3 4 4 12 5 2 6 9 This exercise contains only parts a, b, and c. Part 2 a) The type of control chart that is best to monitor this process is c minus chart ______ . Part 3 b) Using z = 3, the control chart limits for this process are (assume that the historical complaints rate is unknown): UCLc = ________ complaints per week (round your response to two decimal places). The upper control limit is: ________ The lower control limit is: _________ The central limit is ___________
< Refer to Table S6.1 - Factors for Computing Control Chart Limits (3 sigma) for this problem. Sampling 4 pieces of precision-cut wire (to be used in computer assembly) every hour for the past 24 hours has produced the following results: Hour X 1 2 3 4 5 6 R 3.25" 0.65" 3.00 1.23 3.32 1.43 3.39 1.26 3.07 1.17 2.96 0.37 Hour X R Hour R Hour 7 2.95" 0.48" 13 X 3.11" 0.90" 2.73 1.36 19 20 8 2.55 1.18 14 9 0.71 3.12 1.11 21 3.12 2.85 15 16 10 1.38 2.74 0.50 22 11 2.83 1.22 17 2.86 1.38 23 12 3.07 0.45 18 2.64 1.29 24 X 4.51" 2.89 2.65 3.18 3.04 2.54 R 1.56" 1.14 1.13 0.51 1.58 1.02 Based on the sampling done, the control limits for 3-sigma x chart are (round all intermediate calculations to three decimal places before proceeding with further calculations): Upper Control Limit (UCL) = inches (round your response to three decimal places).
A process generating attribute data has an estimated sigma capability = 3.3. Assuming the process mean is shifted +/- 1.5 sigma from the target value, what is the estimated dpmo? Estimated dpmo = ____.
Twelve samples, each containing five parts, were taken from a process that produces steel rods at Emmanual Kodzi's factory. The length of each rod in the samples was determined. The results were tabulated and sample means and ranges were computed. The results were: Sample Sample Mean (in.) Range (in.) Sample Sample Mean (in.) Range (in.) 1 11.404 0.044 7 11.403 0.021 2 11.400 0.051 8 11.407 0.058 3 11.389 0.042 9 11.397 0.039 4 11.406 0.037 10 11.403 0.038 5 11.395 0.048 11 11.401 0.054 6 11.397 0.053 12 11.406 0.061 Part 2 For the given data, the x = enter your response here inches (round your response to four decimal places). The control limits for the 3-sigma R-chart are (round all intermediate calculations to three decimal places before…