2. Determine the reaction at the hinge support at point A and roller support at point B, which is inclined at 30 degrees. Hint: resolve the inclined roller support into its x and y components. A 6 m 4 kN -2 m B 30°

Q: I need help solving problems 7, 8, and 9 pertaining to the print attached below.

A: 7.In question no. 7 information is not enough to answer the question. As there are many circles in…

Q: Some homes that use baseboard heating use copper tubing. Hot water runs through and heats the copper…

A: Mass of the copper tube,(m)=540 g. Initial temperature,(T1)=15.01oC Final temperature,(T2)=25.48oC…

Q: David is working on her farming business and faces the challenge of watering her plants daily, which…

A:

Q: Please walk me through finding how much force the women need to pull the force

A: Given data: Weight is W Need to determine the required force to pull the weight.

Q: I need the answers to this part, I have submitted this question twice on this site and both times…

A: Sampling length – 5 Minimum material to be removed is specified -  1 Rough machine finish – 3…

Q: 1. A) radio wave has a wavelength of 21 cm. What is the wavelength in meters? (Give your answer in…

A: Given data:   wavelength of radio wave = 21 cm speed of light = c = 3 * 108 m/s

Q: Can you help me with this problem? P1 is where the blue dot is

A: 1. N10 G90 - Set to absolute positioning.2. N20 G54 - Select the work coordinate system.3. N30 G00…

Q: The question and data are in pictures. Please answer properly with each steps and explanation. Best…

A: To determine if Column 1 will remain stable if the water tank is placed directly above it, we need…

Q: please help solve A-F. thank you You are an engineer working on a project and your prototype has…

A: LOAD DEFLECTION (LB) (IN) 0 2 3000 2.00167 6000 2.00333 7500 2.00417 9000 2.009 10500 2.04 12000…

Q: Can you write me a program manuscript using geometric definition on FAPT language. The starting…

A: To create a part program for the given part drawing (Fig. 2) for a wire electric discharge machine…

Q: This problem set deals with the problem of non-constant acceleration. Two researchers from Fly By…

A: Given: To find: Write all equations Construct least squares problem Construct system of normal…

Q: An air conditioning unit uses Freon (R-22) to adapt an office room at temperature 25 oC in the…

A: The data given in the problem is, Temperature at condenser, T1 = 48℃ Temperature at evaporator, T2…

Q: gure 4.00 in 1.25 in A single-scoop ice cream cone is a composite body made from a single scoop of…

A: Given:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: first image is blur but second image is clear. so I am solving second image question. Kindly repost…

Q: Can you help me with this please? For a given part drawing fig. prepares a Part program for a wire…

A: To write a part program for a Wire EDM machine using Fanuc - Cut, we need to consider the geometric…

Q: GIVEN THE ORTHOGRAPHIC VIEWS, CREATE AN ISOMETRIC SKETCH OF THE FOLLOWING OBJECT.

A: According to the given data Three projection view of an object is drawn We need to draw Isometric…

Q: You are in an inventory management field these days. You are working for a place which works on 365…

A: The objective of this question is to determine the number of orders per year that should be placed…

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: I need these three parts answered, if you are unable to answer all three parts please leave it for…

A: 4.The number 81073 denotes the CAGE no. as shown in the print. The CAGE code indicates Commercial…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.