2. Carbon steel shaft with diameter of 350 mm is heat treated in a gas fired furnace where the gas in the furnace is at 2000 K and convection coefficient of 25 W/m²K. If the initial temperature of the carbon steel shaft is 500K and the specific heat capacity and density of Carbon Steel are 600 J/kg.K and 7800 kg/m³ respectively; a. How much time does the ball take to be heated to a temperature of 1500K b. What will be the temperature of the ball after 30 minutes of heating c. If you increase the diameter of the shaft two times what will be the duration required for heating the ball to the required temperature of 1500K

2. Carbon steel shaft with diameter of 350 mm is heat treated in a gas fired furnace where the gas in the furnace is at 2000 K and convection coefficient of 25 W/m²K. If the initial temperature of the carbon steel shaft is 500K and the specific heat capacity and density of Carbon Steel are 600 J/kg.K and 7800 kg/m³ respectively; a. How much time does the ball take to be heated to a temperature of 1500K b. What will be the temperature of the ball after 30 minutes of heating c. If you increase the diameter of the shaft two times what will be the duration required for heating the ball to the required temperature of 1500K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve both parts with handwriting please need with correct answer need awesome answer solve both handwriting i requested to u. Part6. An exposed 8 cm external diameter, 20 m long hot-water pipe at 80°C is losing heat to the surrounding (outdoor) air by natural convection. The average outdoor temperature is 5°C. The heat transfer coefficient is 25 W/m2°C. What is the heat loss by natural convection, in kW? A. 9.4 W B. 10.0 W C. 10.4 W D. 11.4 W Part7. A spherical ball with a diameter of 10 cm has an outer surface that is maintained at a temperature of 200°C. It is suspended in the middle of a room that has an average temperature of 20°C. If the surface emissivity is 0.8, determine the rate of radiative heat transfer from the ball to the room in W. (Choose the nearest value) A. 2.3 W B. 4.5 W C. 19.4 W D. 60.8 W
6. a. The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls have a thickness of 10 mm and a thermal conductivity of 12 W/m.K. If the wall surface temperature is measured to be 50oC on the left and 30oC on the right, prove that conduction heat transfer occurs at a steady state!b. Heating the iron cylinder on the bottom side is done by placing the iron on the hotplate. This iron has a length of 20 cm. The surface temperature of the hotplate is set at 300oC while the top side of the iron is in contact with the still outside air. To reach the desired hotplate temperature, it takes 5 minutes. Then it takes 15 minutes to measure the temperature of the upper side of the iron cylinder at 300oC. Show 3 proofs that heat transfer occurs transiently
3.4 Estimate the rate of heat loss due to radiation from a covered pot of water at 95 ° C. How does this compare with the 60 W that is lost due only to convection and conduction losses? What amount of energy input would be needed to maintain the water at its boiling point for 30 minutes? The polished stainless steel pot is cylindrical, 20 cm in diameter and 14 cm high, with a tight-fitting flat cover. The air temperature in the kitchen is about 25 ° C. State any assumptions you make in deriving your estimates
The inside wall of a furnace is at 2100oF and the outside wall is at 300oF. The wall of a furnace must be designed to transmit no more than 220 Btu/hr-ft2. Two types of bricks are available for construction:TYPE A: k = 0.38 Btu/ hr-ft-R with an allowable maximum temperature of 1400oFTYPE B: k = 0.98 Btu/ hr-ft-R with an allowable maximum temperature of 2300oF Both types of bricks have the same dimensions (9” x 4.5” x 3”) but the cost for Type B brick is twice the cost of Type A brick. Illustrate the order of arrangement of bricks A and B in the furnace wall (with thickness, estimated temperatures at the interface between walls A and B and at the interior and exterior surface, the transport area and direction of transfer included)
QUESTION 7 A large slab 1.0 m thick is poured rapidly. The hydration process in the concrete (k=0.84 W/mK) produces an intenal heat generation at a constant rate of 100 W/m3. If the surface temperature of both sides of the slab is 16°C, determine the maximum temperature in the slab. O a. 16 °C O b. 27 °C OC. 37 °C O d. 47 °C O e. 17 °C O f. None of them
Match the appropriate thermal conductivity walue for the given materials Material Thermal Conductivity (K) 4. Diamond 0.026 W/m K B. Copper 2. 0.607 W/m K c. Water 3. 385 Wm K D. Ar 2300 Wm K O a. A-I, B-IV, C-I, D-I O b. A-II, B-I C-I D-IV Oc A-IV, B-II, C-II, D-I O d. A-I, B-I, C-II D-IV
For the calculation of heat transfer by natural transport from a horizontal cylinder, what is the dcharacteristic length found in the number Gr. Please select one: a. Length b. Half of the perimeter c. None of them d.Diameter e. Environment
The inner and outer surfaces of a 1-m by 1-m wall of thickness 100 mm and thermal conductivity 10 W/m. C are maintained at temperatures of 35 C and 15 C, respectively. Determine the heat rate by conduction. Select one: a. 2 kW b. 2 MW c. 20000 W
You are designing a PCB laid horizontally on the ground. The PCB surface temperature can’t exceed 85℃ and has a size of 96mm x 90mm. Tinfinity = 45oC. "p" is the perimeter of the plate a) Calculate the Rayleigh number. b) If the PCB is laid hot-side UP, what is the Nusselt number and heat transfer coefficient? c) If the PCB is laid hot-side DOWN, what is the Nusselt number and heat transfer coefficient? d) Given your results from b and c, which one has better heat transfer? In that case, what is the maximum power dissipation the board can put out? Properties of Air:k = 0.025 W/mkPr = 0.72v = 1.847 x 10−5u = 16.84 x10−6p = 1.2 kg/m3B =1/ Tf (idwal gass)
a. The wall of a building has a surface area of 50 m2. The outside layer of the wall is 20 cm thick concrete with thermal conductivity kcon = .8 W/m-K. The inner layer is 10 cm thick balsa wood (kbalsa = .048 W/m-K) as an insulator. Outside temperatures of 47o C are expected, while an inside temperature of 21o C is maintained by the cooling system. Find the rate of heat transfer through the wall.
A pipe carries hot molten lead from one part of a factory floor to another. The mass flow rate of lead is 0.05 kg/s. While trying to figure out the heat loss from the pipe, you found that over a 2-m length of he pipe the lead temperature drops from 580 C to 557.C. What is the rate at which thermal energy is being lost from the lead carrying pipe in this 2-m section? Use the property table to find out properties of lead as needed.
My buddy is starting to get hypothermic (body temperature 306 K) during an epic backcountry ski adventure. Since I'm quite warm (body temperature 310 K), I decide to get in a sleeping bag with him to try and warm him up. What heat transfer mechanism will be most responsible for heating him up? For simplicity, ignore any internal temperature differences across my body (that is, assume my skin temperature is also 310 K). Use numbers to support your answer (for human skin, you can use the following values: surface area A = 1:50 m2, emissivity = 0:970, thickness d = 0:0250 m, thermal conductivty 0:200 JmsK)