2. An open cylindrical vessel has a diameter of 20 feet and a sidewall height of 8 feet. The dry weight of the vessel is 30 tons. The vessel is floating in seawater. a) What is the surface area of the bottom of the vessel in square feet (ft?)? b) What is the buoyant force in pounds acting on the vessel in the seawater? c) How deep does the bottom of the vessel sink below the surface of the seawater in feet?

2. An open cylindrical vessel has a diameter of 20 feet and a sidewall height of 8 feet. The dry weight of the vessel is 30 tons. The vessel is floating in seawater. a) What is the surface area of the bottom of the vessel in square feet (ft?)? b) What is the buoyant force in pounds acting on the vessel in the seawater? c) How deep does the bottom of the vessel sink below the surface of the seawater in feet?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What will be the diameter (in mm) of a water droplet, the pressure inside which is 0.05 N/cm² greater than the outside pressure? (Take surface tension as 0.075 N/m) a) 3 b) 0.3 c) 0.6 d) 6
Problem 5 Specific Gravity (Gs) Saturation Water content 2.66 100% 49% e = n = Y = % lb/ft³
200 tg • A rectangular boat with additional load at the center of 1200 kg is submerged in water by 1.8 m. The boat is 8 m long and 6 m wide and 2.4 m high. • Find the total draft after the 7280 kg is placed at the edge of the boat without causing it to sink. Assume water is fresh with density equal to 1000 kg/cu.m. • Determine the initial metacentric height. / • Determine the final metacentric height./ • Determine the shifting of the center of buoyancy. /X
What will be the diameter (in mm) of a water droplet, the pressure inside which is 0.05 N/cm² greater than the outside pressure? (Take surface tension as 0.075 N/m) a) 3 b) 0.3 c) 0.6 d) 6
50 I. elearn.nu.edu.om ¥ Question Completion Status: QUESTION 1 10 points Save Answer Compute the effective pressure at a depth of 10m below the bottom of a lake 6m deep. The bottom of the lake consists of soft clay with a thickness of more than 12m. The average water content for the clay is 45% and the specific gravity of soil is 2.65. Assume the lake is filled up with water upto the top. Attach File Browse My Computer Click Save and Submit to save and submit. Click Save All Answers to save all answers. Save All Answers Save and Submit :)
A spherical wooden ball 1 ft. Diameter is used as a float for a boat. If the ball sinks to a depth of 7 in. Find the area of the wetted surface.
For a laminar flow through a channel, Reynold's number is given by 1500, what is the friction factor?
Please show me how to do this problem using the stokes settling velocity equation. Thank you How is water with 120 µm-diameter particles clarified using a settling tank that is 32 m long, 2.1 m wide, and 1.6 m deep? The dynamic viscosity of water is 1.3 x 10-2 g/cm.sec. and the density of the particles is 2.5 g/cm3. What flow rate can be permitted at its maximum to ensure that all the particles land in the tank?
2-16. An important quality characteristic of water is the concentration of suspended solid material. Following are 60 measurements on suspended solids from a certain lake. Construct a stem-and-leaf diagram for these data and com- ment on any important features that you notice. 42.4 65.7 29.8 58.7 52.1 55.8 57.0 68.7 67.3 67.3 54.3 54.0 73.1 81.3 59.9 56.9 62.2 69.9 66.9 59.0 56.3 43.3 57.4 45.3 80.1 49.7 42.8 42.4 59.6 65.8 61.4 64.0 64.2 72.6 72.5 46.1 53.1 56.1 67.2 70.7 42.6 77.4 54.7 57.1 77.3 39.3 76.4 59.3 51.1 73.8 61.4 73.1 77.3 48.5 89.8 50.7 52.0 59.6 66.1 31.6
What is the flow rate of a horizontal rectangular system when the conditions are as follows: Permeability = 1 darcy Area = 9 Ft² viscosity = 1 cp Length = 9 Ft Inlet pressure = 7 atm Outlet pressure = 4 atm
Determine the phase of water at T = 260 C, P = 5MPa T = -2 C, P = 100kPa
600 mm ELABORATE 600 mm Solve for the following buoyancy problems: 1. Water in the container is originally at a height of h = 1 m. If a block having a density of 800 kg/m³ is placed in the water, determine the new level h of the water. The base of the block is square, 600 mm by 600 mm, while the base of the container is 1.2 m by 1.2m. (1.12 m)