2. An abc-sequence, balanced 3-ph supply with a line voltage of 400 V supplies two balanced 3-phase loads that are connected in parallel. The first load is Y-connected and has an impedance of 15-120 0 per phase. The second load is A-connected and has an impedance of 60 + ja5 0. The line has an impedance of 1 + j2 0. Taking the phase voltage Ea as reference, determine the ine currents, the phase currents per load, and the total complex power suppied by the source. "

2. An abc-sequence, balanced 3-ph supply with a line voltage of 400 V supplies two balanced 3-phase loads that are connected in parallel. The first load is Y-connected and has an impedance of 15-120 0 per phase. The second load is A-connected and has an impedance of 60 + ja5 0. The line has an impedance of 1 + j2 0. Taking the phase voltage Ea as reference, determine the ine currents, the phase currents per load, and the total complex power suppied by the source. "

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

q1 B g6= 9 g7 = 8
Example 4 Sequence networks: balanced-Y and balanced-A loads A balanced-Y load is in parallel with a balanced-A-connected capacitor bank. The Y load has an impedance Zy = (3 + j4) 2 per phase, and its neutral is grounded through an inductive reactance X, = 2 Q. The capacitor bank has a reactance X. = 30 N per phase. Draw the sequence networks for this load and calculate the load-sequence impedances. 16
Power system class, can you please show steps so I can understand
Answer number 2
Question 1 (Mandatory) If the a digital pattern repeats itself as 000111111100011111110001111111 .…...... the time interval for each logic state is 0.1 ms, what is the frequency and duty cycle of this digital waveform? 1 kHz, 30% duty cycle. 1 kHz, 70% duty cycle. 10 kHz, 70% duty cycle. 1 kHz, 80% duty cycle. Question 2 (Mandatory) The hexadecimal equivalent for decimal 922 is A93. 39A. 1093. 3910.
None
Calculate the line currents in the following 3-phase balanced system (at load). The voltage source connected to the load is in the form va (t) = 100.coswt and phases b and c are offset by 120 degrees. Does a current flow through the delta connection? Prove it and show it with calculation. LA ICA A IAB 20/45° Ω VCA VAB 20/45° B - 20145° N VBC Ic
Solve with clear steps
In a positive sequence Y-connected three phase balanced system, the phase voltage in phase (a) is given as Vm = 5e7/4_ What is the line voltage Veg? Select one: O a 5e(=/4-x/2) O b. 5/3e(#/4+/2) Oc. 5/3e(=/4+=/6) Od. 5e(#/4+2w/3)
Q2 (a) Based on the relationship between the line and phase value of currents and voltage, show that the active power input to a three-phase balance load is v3VIcosø, where V and I are line quantities. (b) A balanced Y-connected load has phase voltage of 230 V and positive phase sequence. The impedances ZĄ, ZB, and Zc are 10230° N, respectively. (i) By taking VAB On the load side as a reference, determine all the line currents and phase voltages. (ii) Determine total real power, P, total reactive power, Q and total apparent power, S of the system. (iii) Total real power of the loads can be measured using two wattmeter methods. Draw the connection of the two wattmeters if their current coils are in line A and C, respectively. What is the total real power measured by each wattmeter? Prove and compare the value with Q2(b)(ii).
A three-phase positive sequence Y-connected source supplies 14kVA with a power factor of 0.75 lagging to a parallel combination of a Y-connected load and a A-connected load. The Y- connected load uses 9kVA at a power factor of 0.6 lagging and has an a- phase current of 10/30° A. a) Find the complex power per phase of the A-connected load. b) Find the magnitude of the line voltage.
4. I need help with this practice problem