Consider the given circuit. n 12+ R www www Rw Z.p a Le Vbn b Rw ww B For the balanced three-phase system, it is determined that 100 W is lost in each wire. If the phase voltage of the source is 400 V, and the load draws 10.00 kW at a lagging PF of 0.83, determine the wire resistance Rw (Round the final answer to three decimal places.) The value of the wire resistance Rwis Ω.

Consider the given circuit. n 12+ R www www Rw Z.p a Le Vbn b Rw ww B For the balanced three-phase system, it is determined that 100 W is lost in each wire. If the phase voltage of the source is 400 V, and the load draws 10.00 kW at a lagging PF of 0.83, determine the wire resistance Rw (Round the final answer to three decimal places.) The value of the wire resistance Rwis Ω.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

part (iii) please
Q27. a) What do you mean by P controller ?.Draw the electronic circuit of P controller and also write the electronic output equation and General controller output equation . b) Draw the symbol of EXNOR gate.Also write the Truth table and Ladder diagram of EXNOR.
5.- Design a microcontroller system to control a sprinkler controller that performs the following tasks. We assume that your microcontroller is clocked at 10 MHz and has a 16-bit free-running counter. The sprinkler controller system controls two different zones by turning the sprinklers within each zone on and off. To turn on the sprinklers in a zone, the controller needs to receive a 152.589 Hz PWM signal from its microcontroller. To turn off the sprinklers in the same zone, the controller needs to receive the PWM signal with a different duty cycle. B.- After 15 min, your microcontroller must send the PWM signal with a 15% duty cycle of 10 ms to turn off the sprinklers in zone one.
Mention three applications where PID controller can be used. Explain them each in a paragraph.
C o pied answers will be disliked
23 - Mathematical model of control system is ... A) mathematical expression of a system which has not a memory and output variables O B) mathematical expression of a system in that the variables are time-independent C) Mathematical expression which describes the relationships among system inputs, outputs and other inner variables O D) mathematical expression of a system which describes interconnection via inner variables E) mathematical expression of a system which has a memory and input variables
a) A new manufacturing plant which operates on parameters such as temperature and pressure, has been procured by your company. In the operational manual is stated "if one or more than one parameter exceeds the safe value, a protective measure is needed to be done". As an engineer, design a schematic diagram using an OR gate to detect the exceed parameter and explain how it will produce a command signal for the system to take the required action.
Solve it on paper using function block diagrams
((What are electronic sensors))? ((Which consists))? ((Types))? (At least ten types of medical sensors) their uses? (Preferably with Arduino) ((Its applications and the projects in which it is used))? ((How to use it))? ((Programming languages, programs and controllers that deal with))? ((Its advantages and disadvantages))? It is preferable to make an example of the Arduino, whether in form or in practice
Solve it fast fast plz
Petroleum Systems Control Department Digital Technique LAB Experiment No. (5) Procedure: 1. Connect the logic circuit required to implement the function F in equation below and write the truth table for the circuit: F(X,Y,Z)= XYZ+ XYZ + XYZ + XYZ + XYZ 2. Connect the logic circuit required to implement the function Z in equation below and wri the truth table for the circuit: FI(X,Y,Z)= (X+Y+Z) (X+Y+Z) (X+Y+Z) 3. Derive the Boolean Algebra expression for a gating network that will have outputs "0" only when: (X-1,Y=1,Z=1) (X=0,Y=0,Z=0) (X=1,Y=0,Z=0) the outputs are to be "1" for all other cases? 4. Connect the circuit which derived in step 3 and write the truth table for it ?. 5. Express using (sum of Minterms) and (product of Maxterms) for F shown in the table (5-1) bellow?. 6. Connect the circuit that implement F in step 5 and find the truth table for it Practically?. Table (5-1) Y Z 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1