A three-phase impedance load consists of a balance A load in parallel with a balance Y load. The impedance of each leg of the A load is ZA= 27+ j6 Q, and the impedance of each leg of the Y load is ZY = 1+ j10. The Y load is grounded through a neutral impedance Zn= j1/3N. Unbalanced line-to-ground source voltages Vag, Vbg, and Vcg with sequence components V0= 10 L60°, V1= 100 L0°, and V2 = 15 L200° volts are applied to the load. 10 is equal to (hint: draw the zero, positive and negative sequence networks): %3D

A three-phase impedance load consists of a balance A load in parallel with a balance Y load. The impedance of each leg of the A load is ZA= 27+ j6 Q, and the impedance of each leg of the Y load is ZY = 1+ j10. The Y load is grounded through a neutral impedance Zn= j1/3N. Unbalanced line-to-ground source voltages Vag, Vbg, and Vcg with sequence components V0= 10 L60°, V1= 100 L0°, and V2 = 15 L200° volts are applied to the load. 10 is equal to (hint: draw the zero, positive and negative sequence networks): %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A three-phase substation bus supplies a wye and a delta connected constant impedance loads. The loads are connected in parallel. A three-phase feeder with an impedance per phase of Z = 0.6+j1.8 Q connects the loads to a source as shown in the one- line diagram of Figure below. The loads draw the following three-phase power: P1 = 35 kW S2 = 30 kVA pfi = 0.90 (leading) pf2 = 0.85 (lagging) wye connected delta connected The line-to-line load voltage is 480 V. Detemine: (a) the impedance of each load per phase, (b) the total line current flowing through the feeder, (c) the line-to-line voltage at the substation bus, and (d) the total three-phase real and reactive power supplied by the bus. Zfeed Vbus
Answer number 6 please
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
Q2
Phase Qz/ The eas Voltages at the terminal of abalan ced Y connected load is VAN=12o 28. Each Phase of the load consist of lo 230° .Find the active & Reactive and Complex Power Per-Phase then find the total Powers For three Phase load.
Line Voltages at the terminal Pz:- The of abaancat Y conmected load is----- Each Phase of the load cousist of loL30 S2 Find the active s Reactive and somflex Power fer Phase then Find the total load. Var=12010, Powers for Heree phase
Pz:- The of abalanced Y connected load is- Each phase of the load cousist of loL30 s2 Find the Line Voltages at the terminat actives Reachive and somflex Power Per Phase then Find the total Powers For Heree phase load. VAB =10010for 4
2. A single-phase a.c. distributor AB is fed from end A and has a total impedance of (0-2 + j 03) ohm. At the far end, the voltage V = 240 V and the current is 100 A at a p.f. of 0-8 lagging. At the mid-point M, a current of 100 A is tapped at a p.f. of 0-6 lagging with reference to the voltage Vy at the mid-point. Calculate the supply voltage V, and phase angle between V, and Vg- [292 V, 2-6°] a loade
1. Given the circuit below, the phase voltages are given by Van = 20040° Vrms. The source impedance is 5 + j7 per phase and the wire impedance is 8 +j10 per phase. Let the load impedance be Zy = 50 ohms. Find: Van Vin Ven a. II, and Ic b. c. VAN, VBN, and VCN, and VAB, VBC, and VCA Z₂ Z₂ Z₂ Zw Zw Zw B C le N
i need the answer quickly
Q-3-) a V346.41 V b Z=0+339 Z=0+j3Q Z=0+/39 m Line V₂ R R R=1252 Star-Connected load R b-) Find the voltage drop value in the energy distribution line. c-) Find the voltage V₂ at the load ends at the end of the line. R B R R=1892 Delta-Connected load In the figure above, two balanced 3-phase delta and star-connected loads are connected in parallel to a balanced three-phase power distribution line. Delta and star connected loads are completely resistive and the resistance values per phase are 18 2 and 12 22, respectively. The phase-to-phase voltage value of the source feeding the line is 346.41 V (rms), and it is assumed that the three-phase network between the source and the load has an inductive reactance value of 3j 2 per phase. a-) Find the total current drawn from the source, active and reactive power values by selecting the Van voltage as a reference value.