2. A thin-walled cylindrical pressure vessel, which has an internal diameter d = 840 mm, is designed to resist an internal pressure p = 7 MPa and a compressive load F = 600 KN that is applied on the two ends of the vessel (see Figure Q2). The allowable shear stress in the wall of the cylinder is 80 MPa. Determine the optimum thickness, t of the vessel? Cylindrical Vessel Figure O2 1

2. A thin-walled cylindrical pressure vessel, which has an internal diameter d = 840 mm, is designed to resist an internal pressure p = 7 MPa and a compressive load F = 600 KN that is applied on the two ends of the vessel (see Figure Q2). The allowable shear stress in the wall of the cylinder is 80 MPa. Determine the optimum thickness, t of the vessel? Cylindrical Vessel Figure O2 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rod shown in the figure has two cross-sectional areas, where the area of the larger cross-section is 6 times larger than the smaller. The rod is subjected to three point loads, P₁, P2, and P3 at points B, C, and D, respectively. You may assume that the bar deforms in a linear-elastic manner. The cross section of the small rod is equal to A = 2 in² and the modulus of elasticity is equal to E = 20,000 ksi. a) Find the support reactions at A and E, if P₁ = b) Draw the axial force diagram. c) Identify how the position of point C changes due to the applied loadings. A 12 in B P₁ 11 in C 10 kips, P₂ = 20 kips and P3 = 40 kips. P₂ 11 in D P3 E the axu 12 in
A thin-walled cylindrical pressure vessel of inner radius r = 0.6 cm and a thickness of 0.06 cm is subjected simultaneously to internal gas pressure p = 3.5 MPa, a compressive force F = 800 N acting at the ends, and a torsional load of 25 N · m (see figure). Determine the following quantities (a) the principal stresses at a point H on the surface of the vessel and the absolute maximum shear stress; (b) the normal strain along x-axis (ɛx) and the shear strain (yxy) at the same point H. See the established Oxy coordinate system. The Young's modulus of the material is 200 GPa and the Poisson's ratio is 0.3. Hint: the cross-section of the vessel can be regarded as a hollow tube and the cross-section area can be calculated as 1(0.00662 – 0.006²). You can do the same treatment for the polar moment inertia. 25 N· m F F H X 25 N· m
An element is composed of a circular steel tube, which is enclosed by a steel cylinder as shown in the figure. The element is subjected to a compressive force P=20 KN. The aluminum cylinder has an outside diameter of 10 mm and a modulus of elasticity Ea=75 GPa. The steel tube has an outer diameter of 3 mm and a modulus of elasticity Eac = 190GPa. The element has a length L = 200 mm. Determine: compressive stresses in aluminum cylinder and steel tube. the compressive forces in the aluminum cylinder and the steel tube. The contraction of the element product of the force P.
Answer quickly
A circular aluminum tube of lengthL = 600 mm is loaded in compression by forces P(see figure). The outside and inside diameters ared2 = 75 mm and d1 = 63 mm, respectively. A straingage is placed on the outside of the tube to measurenormal strains in the longitudinal direction. Assumethat E = 73 GPa and Poisson’s ratio is n = 0.33.(a) If the compressive stress in the tube is 57 MPa,what is the load P?(b) If the measured strain is ε =781x10 -6 , what isthe shortening δ of the tube? What is the percent change in its cross-sectional area? What is thevolume change of the tube?(c) If the tube has a constant outer diameterof d2 = 75 mm along its entire length L butnow has increased inner diameter d3 with a normalstress of 70 MPa over the middle third (seefigure, part b) while the rest of the tube remains atnormal stress of 57 MPa, what is the diameter d3?
A horizontal load P is applied to an assembly consisting of two inclined bars, as shown in the figure. The cross-sectional area of bar (1) is 1.30 in.2, and the cross-sectional area of bar (2) is 1.75 in.2. The normal stress in either bar may not exceed 24 ksi. Determine the maximum load P that may be applied to this assembly. Assume dimensions of a=14.5 ft, b=9.0 ft, and c=14.5 ft. Determine the allowable force F1 in member (1) and the allowable force F2 in member (2).
n the figure below, a member is subjected to an axial force P. If the cross sectional area of the member is denoted as AB, then the maximum value of its normal stress occurs when: ∅ = 00 ∅ = 300 ∅ = 450 ∅ =900
A 30 mm square is drawn on the rim of a large steel pressure vessel. The biaxial stress situation in the square after the pressure is applied is as shown in the figure. Determine the change in length of the BC edge in (mm).
The pins at B and D in the figure apply an axial load to diagonal bracing member BD. If BD has a rectangular cross-section measuring 0.50 in. X 2.00 in., what is the axial stress in member BD when the load is w0=220 lb/ft?
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 50 MPa and Sy = 250 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 46°.
(3): A steel bar ABCD (4m) long is subjected to forces as shown in Figure. Find the stresses in each part. d=20 mm d=15 mm d=15 mm В D 20 kN 25 kN 5 kN 10 kN (4): A round tapered alloy bar (4m) long is subjected to load as shown in Figure. Find the stresses in section at point (B) and section at point (C). D B 30 kN. 50 kN 70 kN 50 kN d=20 mm d=40 mm 1m 2 m 1m
In mechanical resistance