2.) A steam power plant operates on the ideal Rankine cycle producing a net power output of 120 MW. The maximum pressure of the cycle is 15 MPa, and the minimum pressure is 5 kPa. Steam initially enters the turbine at 500 C. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.) Find the quality of the steam entering the condenser, Qa, Qr, Wt, Wp, Wnet, efficiency, mass flow rate and steam rate

2.) A steam power plant operates on the ideal Rankine cycle producing a net power output of 120 MW. The maximum pressure of the cycle is 15 MPa, and the minimum pressure is 5 kPa. Steam initially enters the turbine at 500 C. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.) Find the quality of the steam entering the condenser, Qa, Qr, Wt, Wp, Wnet, efficiency, mass flow rate and steam rate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

boiler turbine condenser In an ideal reheated Rankine cycle, water vapor enters the high pressure turbine at a temperature of 400 °C and a pressure of 3 MPa and exits at a pressure of 0.8 MPa. After the water vapor is reheated to 400 °C, it enters the low pressure turbine and expands to a pressure of 10 kPa. a) Find the total amount of heat given to the water vapor (kJ/kg). b) Calculate the thermal efficiency of the cycle. c) Show the cycle in the T-s diagram.
For an ideal Rankine cycle, steam first enters the turbine at 5 MPa and 500C then it expands to a pressure of 100 kPa. a.) Draw the proper T- S diagram of the cycle with proper label for the points. b.) Find the quality of the steam, Qa, Qr, Wt, Wp, Wnet, efficiency, and steam rate.
A steam power plant is operating on the ideal Rankine cycle. The boiler is maintained at 4 MPa, and the condenser at 40 kPa. The steam quality leaving the turbine is at 90%. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.) Find the temperature of the steam entering the turbine, Qa, Qr, Wt, Wp, Wnet, efficiency, and steam rate
boiler In an ideal reheated Rankine cycle, water vapor enters the high pressure turbine at a temperature of 400 °C and a pressure of 3 MPa and exits at a pressure of 0.8 MPa. After the water vapor is reheated to 400 °C, it enters the low pressure turbine and expands turbine to a pressure of 10 kPa. a) Find the pump work (kJ/kg). b) Find the degree of dryness at the exit of the water vapor from the low pressure turbine. c) Find the turbine work (kJ/kg). condenser
3.) In In an actual Rankine cycle, steam first enters the turbine at 10 MPa and 400C. It expands to a pressure of 10 kPa as saturated vapor and it then enters a pump with 85% efficiency after condensing. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.) Find the quality of the steam, Qa, Qr, Wt, Wp. Wnet, efficiency, and steam rate kg kWh 2892.802392.87511.8 11.87 499.93 17.28%, 7.20 kg kg
A rankine cycle with water superheats to 500.546oC at 3.1546 Mpa in the boiler and the condenser operates at 100.546oC. All the components are ideal except the turbine which has an exit state measured to be saturated vapor at 100.546oC. Find the cycle efficiency with a) an ideal turbine and b) the actual turbine. Draw the schematic diagram and T-s diagram.
Problem (1.2) A steam power plant working according to simple Rankine cycle. It has a high pressure of 3 MPa and it maintains 60°C in the condenser. A condensing turbine is used, but the quality should not be lower than 90% at any state in the turbine. Find the cycle efficiency. [reference: Fundamentals of Thermodynamics by Borgnakke & Sonntag prob.11.18,p-460].(Ans.33.2 %).
In an ideal Rankine cycle, steam first enters the turbine at 10 MPa and 400C. It expands to a pressure of 10 kPa. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.) Find the quality of the steam, Qa, Qr, Wt, Wp, Wnet, efficiency, and steam rate
In an ideal open feedwater heater Rankine cycle, water leaves the condenser at 100 kPa and from the boiler at 500 *C and 3 MPa pressure. The water emerges as a saturated liquid at 400 kPa pressure from the open feed water shown in the figure. According to this; a) Show the cycle in a T-s diagram with saturated liquid and saturated vapor curves. b) Find the total pump work (kJ/kg). c) Find the ratio (y) of the mass of steam leaving to heat the turbine feedwater to the mass of steam entering the high pressure turbine. d) Find the turbine work (kJ/kg). e) Find the amount of inlet 1 (kJ/kg). f) Find the efficiency of the cycle.
A simple ideal Rankine cycle operates in the pressure range of 50 kPa to 3 MPa. Water vapor enters the turbine at a temperature of 300 oC and a flow rate of 35 kg/s. a) Find the enthalpy values of all points. b) Find the thermal efficiency. c) Find the net power.
A steam power plant operating on iregenerative cylce includes one feedwater heater [back word]. steam enters the turbine at 4500KPA and 500C and extracted from the turbine at 350KPA. what is thermal efficiency of the cycle ? TTD = 5
1. Determine the Rankine efficiency of a condensing steam turbine operating in a Rankine cycle as follows: Steam pressure - 200 psiaSteam temperature - 1000 FExhaust pressure - 2 in Hg absoluteSteam rate - 1.5 lb/kW-hr 2. If the no. 1 problem has a thermal efficiency of 30%, how many barrels of 30 °API fuel oil will be required to produce 1000 kW-hr of power. Neglect the pump work.