The x- and y-motions of guides A and Bwith right-angle slots control the curvilinear motion of the connecting pin P. which slides in both slots. For a short interval, the motions are governed by x = 22 +0.7312 and y = 21-0.641, wherex and y are in millimeters and t is in seconds. Calculate the magnitudes of the velocity v and acceleration a of the pin for t = 3.0s. Sketch the direction of the path and indicate its curvature for this instant. Part 1 Calculate the x- and y-components of the velocity. Answers: Vx i mm/s Vy= i mm/s

The x- and y-motions of guides A and Bwith right-angle slots control the curvilinear motion of the connecting pin P. which slides in both slots. For a short interval, the motions are governed by x = 22 +0.7312 and y = 21-0.641, wherex and y are in millimeters and t is in seconds. Calculate the magnitudes of the velocity v and acceleration a of the pin for t = 3.0s. Sketch the direction of the path and indicate its curvature for this instant. Part 1 Calculate the x- and y-components of the velocity. Answers: Vx i mm/s Vy= i mm/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

HANDWRITTEN. answer 4 5 6 then box the final answers
What is the hardening exponential n and deformation rate sensitivity exponential m ? Comment similar or different aspects, their numerical values should be big or small and changes with temperature
I need question 10 answered please and thank you. Question pertains to the print provided and also the sequence of operations listed in the directions.
Answer the questions below, (Insert the numerical value only, do not use ,+, *, or /) The Relative error for your answer should be less than 0.01, which means if the answer was 50, then the error should not exceed 50*0.01= ±0.5! if the answer was 230, then the error should not exceed 230*0.01= +2 3! if the answer was 2.31467*10^ 3, then you should enter this value: 0.00231467, not this 0.0023 !!!! K2 K1 M1 fv1 M2 f(t) if M1=4, M2=3, fv1=7, K1=4, K2=6. Find the state equations for the translational mechanical system shown in Figure. [d/dt(r1) d/dt(v1) [(1.1) (1.2) (1.3) (1.4) rl (1)] (2.1) (2.2) (2.3) (2.4) (3.1) (3.2) (3.3) (3.4) [(4.1) (4.2) (4.3) (4.4)] vl * f(t)$$ $$ d/dt(r2) d/dt(v2) r2
Could you please spreate each question alone because there are two questions
Please the answer provided is not clear, some words and letters not clear, can you please type the answer or write clearly so that I can see
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
Please answer from iv onwards as you have already sent me the answer to the other please show working and correct answer
f) Answer the question shown in the images. Show every step
Oz Lawn Care Inc. manufactures and assembles lawnmowers that are shipped to dealers throughout the United States and Canada. Two different procedures have been proposed for mounting the engine on the frame of the lawnmower. PB (Minutes) UPB (Minutes )345798632 5 Is there a difference in the methods' mean time to mount the engines on the frames of the lawnmowers? The answer must be in handwriting. Please write your answer using a ball - point pen on plain paper. Submit your homework by uploading it to the canvas. Good Luck!
please hand written solution please hand written solution please hand written solution