2. A shaft with a constant diameter of 2" is loaded by torques applied to gears attached to it as shown. Using G = 12 x 10 psi, determine the relative angle of twist (in degree) of gear A relative to gear D. Use 2 decimal places. Use the given sign convention for uniformity. Provide a torque diagram. 600 lb ft 1000 lb ft 900 lb ft D 500 lb ft 5 t (+) A

2. A shaft with a constant diameter of 2" is loaded by torques applied to gears attached to it as shown. Using G = 12 x 10 psi, determine the relative angle of twist (in degree) of gear A relative to gear D. Use 2 decimal places. Use the given sign convention for uniformity. Provide a torque diagram. 600 lb ft 1000 lb ft 900 lb ft D 500 lb ft 5 t (+) A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the design of the band brake shown, find the couple M required to turn the pipe in the V-block against the action of the flexible band. A force P = 31 lb is applied to the lever, which is pivoted about O. The coefficient of friction between the band and the pipe is 0.26, and that between the pipe and the block is 0.35. the weights of the parts are negligible. B M * 10" 45% 00 35° 35° 5 A Answer: M = | the tolerance the tolerance is +/-5% lb-in. 16" P
ENGINEERING MECHANICS: STATICS (J.L.MERIAM) 2/8: Two forces are applied to the construction bracket as shown. Determine the angle o which makes the resultant of the two forces vertical. Determine the magnitude R of the resultant. F = 800 N F 425 N 70
The solid 50 mm diameter shaft is used to transmit torques applied to the gears. Determine the relative distance of gear D relative to gear A in rad. Use G = 83 MPa. 250 N•m 75 N.m A 325 N-m 150 N-m B 500 mm C 400 mm 500 mm 3.21 2.36 1.18 4.26
A 200-mm diameter pulley is prevented from rotating to 60-mm diameter shaft by a 70-mm long key. If a torque T = 2.2 kN.m is applied to the shaft, determine the width b (mm) if the allowable stress in the key is 60 MPa. 70 mm Shaft 그0 200 mm-e Shaft 60 mm-s-
2 Knowing that a beam of the cross section shown is bent about a horizontal axis and that the bending moment is 6 kN · m, deter- mine the total force acting on the top flange. 54 mm Ce -216 mm y $ C 72 mm 36 mm 108 mm R
To facilitate shifting the position of a lifting hook when it is not under load, the sliding hanger shown is used. The connections at A and B are smooth. Compute the magnitude (N) of the force at A when the hook supports a 202-kg mass and x 0.34 mm and %3D = 0.57 mm. Round off only on the final answer expressed in 3 decimal places. 055.png •.. y mm mm B
Use the diagram shown above. Given • D₁ = 8 ft . • D₂ = 6 ft D3 = 3 ft W = 100 #/ft D3 • P= 200 # Solve for the internal moment at X. D₁ D 2 X W P Note: Enter the numerical value only for your calculation results. You'll be asked to specify the unit for your calculation result in the following question. (This is due to Canvas' lack of ability to require units for calculation question.)
A worker applies the forces P = "-50i" + 40j N and Q = 50i N to the hand- grips of the electric drill. These forces are equivalent to the force R = 40j N acting at the tip of the drill and the couple C = "-1800j" N mm Determine the dimensions a and b.
The weight W of a traveling crane is 20 tons acting as shown. To prevent the crane from tipping to the right when carrying a load P of 20 tons a counterweight Q is used. Determine the value and position of Q so that the crane will remain in equilibrium both when the maximum load P is applied and when the load Pis removed. W=20 tons P=20 tons -10-
Consider (Figure 1). The cord is attached to the 39-lb block, and the coefficients of static friction are μ = 0.2 and HD = 0.3. Figure 1.5 ft B 3 ft -1.5 ft- D C 1 of 1 > Determine the smallest couple moment which can be applied to the 26-1b wheel that will cause impending motion. Express your answer in pound-feet to three significant figures. IVE ΑΣΦ ↓↑ vec M = Submit Provide Feedback Request Answer ? lb ft
Given the data as shown in the figure, determine the (a) maximum torque Tmax (N-mm) that maybe exerted by the twisting tool and the (b) angle of twist (degree). Use G = 78 GPa and Tallowable = 70 MPa. Use 2 decimal places. d = 10.0 mm T L 300 mm
Replace the loading on the frame by a single resultant force. Suppose that F₁ = 450 N F₂ = 650 N, F3 = 950 N, and F₁ = 600 N. (Figure 1) igure F₁ 0.5 m F₂A -1 m- 1.5 m 1m B T0.5 m x 1 of 1 ▼ Express your answer to three significant figures and include the appropriate units. FR = Submit Part B 0 = Submit Part C O x = μA Value Determine the angle between the resultant force and the x axis. Express your answer using three significant figures. VE ΑΣΦ || Ivec Request Answer Request Answer Units μA Value ? Specify where the line of action of the resultant force intersects a horizontal line along member CB, measured from end C. Express your answer to three significant figures and include the appropriate units. Enter positive value if the line of action intersects a horizontal line CB to the right from end C and negative value if the line of action intersects a horizontal line CB to the left from end C. Units ? ? °, measured clockwise from the positive x axis