2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm A 750 B 200 Z2= 38 Z₁ = 19

2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm A 750 B 200 Z2= 38 Z₁ = 19

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The gears shown in the figure form an ideal transmission mechanism. Shaft a applies 8.7 Nm of torque to the pinion (gear 2), which rotates clockwise at 2,312 revolutions per minute. All of the gears have a 20 degree pressure angle. Gears 2 and 3 have a module of 2.5 mm, while gears 4 and 5 have a module of 4 mm. What is the speed of shaft c? Express your answer in units of revolutions per minute. McGraw-Hill Companies, Inc for y 12T NO # + C 3 36T- to 스 3/2 X 18T 30T 5
A 2hp motor is to drive a food shredder. The motor is projected to run at 1450 rpm and the required speed at the food shredder is 60 rpm. Design a double reduction drive consisting of belt and chain for this application. Please give solution and show drawing if needed
As shown in the figure, 2 lumped masses that are not in the same plane are connected to a shaft between the bearings at A and B. The spindle is rotated counterclockwise with a constant speed of 1450 rpm. Perform the dynamic balancing of this prototype rotor system. -Required corrective masses in the L and R planes from the C axis of rotationIt will be placed at a distance of 50 mm. -The values of the required corrective masses will be found in grams. -The angle positions of the necessary corrective blocks will be written in polar style at the last stage. -For the solution, the "Algebraic Solution" method based on Cartesian components will be used.
5. For the engine-transmission-propeller problem shown below, The engine generates a torque of 219lb-ft, and it is bolted to a frame at locations A and B. The transmission reverses the rotation direction. The transmission ratio is 1.5 (i.e. the propeller speed is -1/1.5 the engine speed, the minus sign indicates the change in direction). d. Sketch the free body diagram. Be sure to show the torques at the input and outputs to the different components. Note the change in the rotation direction between the engine and shaft. e. Solve for the reaction forces at the bolt supports of the engine, if the distance between them is 1 ft. Propeller Engine Reduction ratio 1.5 Engine is attached B
A single-strand roller chain drive connects a 50-hp engine to a lawn waste chipper/shredder, as shown below. As the engine operates at 1000 rpm, the shredding teeth should rotate at 250 rpm. The driven sprocket has 60 teeth. Determine the chain speed.
A parallel helical gear set of 19 tooth pinion is driving a 57 tooth gear. The helix angle of 20 degrees while the normal pressure angle is 14.5 degrees and the normal diametral pitch of 10 teeth/inch. If the pinion is rotating at 1800rpm and transmits 50hp, find the normal force. Please answer in detailed solution.
The picture shows the rear swivel axle bearing design of a 4-wheel wagon. It is known that the speed of the wagon wheels is n = 37 rpm. The total radial load carried by the wagon is given as Fr= 16060 Newtons. In addition, due to road conditions, Fa axial load is applied to the wagon. If the axial load on the A bearing is 10% of the radial (vertical) load on this bearing, calculate the dynamic load number (C) of the bearing in the A bearing in Newtons for 18616 hours of life. fo*Fa/Co = 0.345 Pi=3.14
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 ifits gearbox 5th gear is selected. The gear’s teeth are of involute form with amodule of 8 mm, an addendum is double the module, and the pressure angle isequal to 20° .1.1. If the driving shaft of the front wheels of the truck is connected to the output shaftof the gearbox, determine the number of teeth on the pinion to avoid interferenceand the corresponding number of teeth on the gear wheel.
A belt conveyor transports 18 tonnes per hr at 20°. Calculate the height in m to lift the load vertically up sufficient to give 33.5 m inclined belt length. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14,5. The wheelchair has a maximum velocity of 5 m/s when it's pinion rotates at 800 rpm. Calculate : 1.1)The magnitude of the velocity of slip of gears in mesh 1.2)The angular speed of the gear wheel in rad/s 1.3)The maximum length of a path of the approach in mm 1.4)The length of a path of a recess in mm. 1.5) The addendum of the gears in mm. 1.6) The contact ratio
A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum. The 48V DC motor selected has a no-load angular velocity of 800 RPM and a stall torque of 500 inch-pounds. A gearbox has been designed to spin the drum as quickly as possible. Assume that there are no friction losses in this system. The drum is driven by a 72-tooth gear with a diametral pitch of P=8. Assuming that the entire output torque required to turn the drum is produced by the force on one tooth, and that the gear tooth would fail by being sheared off at the pitch circle, determine the required gear face width, b, for a factor of safety of 3 A gear made out of 6061 Aluminum (σy = 35 ksi, τy = 20)
1. A 10 hp. 1400 rpm motor uses a roller chain to drive a line-shaft at 400 rpm with a center to center distance of 2 ft. The motor shaft has a diameter of 1 % inches and the load applied is moderate shock. Determine the approximate length of the chain.