2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E = 83 GPa. Compute the tangential stress in the tube. Answer: o, = 5.20 MPa

2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E = 83 GPa. Compute the tangential stress in the tube. Answer: o, = 5.20 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

> * The state of two-dimensional stresses acting on a concrete lamina consists of a direct tensile stress o. = 1.5 N/mm² and shear stress T = 1.20 N/mm², when cracking of concrete is just impending. The permissible tensile strength of the concrete is
Define the below ? Lateral strain is considered – Skempton–Bjerrum method
The modulus of elasticity is measured as the secant for a stress at: a) 30% b) 45% c) 25% d) 40%
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m 10KN 0.8m 0.4m 5KN 0.6m What is the deformation 8Rc in mm? Al 20KN A=800 mm? A=1,200 mm²
In a tensile test, Load and Elongation are Normalized to Engineering Stress and Engineering Strain . Why?
If the lateral compressive strain in a material is 0.3 x 10-3 and the Poisson ratio is 0.25, then longitudinal strain in the material is ✓ 0.0012 (tensile) 0.0012 (compressive) 7.5 x 10-5 (compressive) 7.5 x 10-5 (tensile)
2. Which of the below stresses are normal stresses? a) Tensile and compressive stresses b) Tensile and thermal stresses c) Shear and bending d) Compressive and plane stresses bolleo
PLEASE SHOW THE COMPLETE AND CORRECT SOLUTION with fbd. Please don't post this question on google. Please. Subject : Strength of Materials ( Economic Section)
Find the elastic strain when total yield strain is 0.005in/in.
A hollow steel cylinder 3.5m which has an inside diameter and outside diameter of 55mm and 35mm. If the steel carry a load (Your Registration Number ie 1 to 63) KN find the stress in the cylinder also find the deformation in the cylinder if the Modulus of Elasticity is 90 GPA.
DURING THE STRESS-STRAIN TEST, THE UNIT DEFORMATION AT A STRESSOF 30 MPa WAS OBSERVED TO BE 110 x 10-6 mm/mm AND AT A STRESS0F 130 MPa IT WAS 520 X 10-6 mm/mm. IF THE PROPORTIONAL LIMITWAS 250 MPa, WHAT IS THE MODULUS OF ELASTICITY? WHAT IS THESTRAIN CORRESPONDING TO A STRESS OF 150 MPa?
2. When a cylindrical body is subjected to uniaxial tensile force, which types of stresses are formed within the body? Show the locations of stresses on an appropriate sketch. 3. (a) If you were designing a metallic tool to be used at very low temperatures (negative temperatures), which material class would be the best option? (b) If you wanted to increase the strength of that tool for that very low temperature, which strengthening method would be the best option? Briefly explain your answer.